Maintenance - Makita DUC256 Betriebsanleitung

WORKING WITH THE CHAIN SAW
CAUTION:
Keep all parts of the body away
from the saw chain when the motor is operating.
CAUTION:
Hold the chain saw firmly with
both hands when the motor is running.
CAUTION:
Do not overreach. Keep proper
footing and balance at all times.
NOTICE:
Never toss or drop the tool.
NOTICE:
Do not cover the vents of the tool.
Pruning trees
Bring the chain saw body into contact with the branch to
be cut before switching on. Otherwise it may cause the
guide bar to
in injury to
the wood to
by just moving
by using the
saw. ►
Fig.20
If you cannot cut the timber right through with a single
stroke:
Apply light pressure to the handle and continue sawing
and draw the chain saw back a little. ►
When cutting thick
make a
undercut and
the finish
top. ►
the
If you try to cut off thick branches from the bottom, the
branch may close in and pinch the saw chain in the cut.
If you try to cut off thick branches from the top without a
shallow undercut, the branch may splinter. ► Fig.23
Carrying tool
Before carrying the tool, always apply the chain brake
and remove the battery cartridges from the tool. Then
attach the guide bar cover. Also cover the battery
cartridge with the battery cover.
►
Fig.24: 1. Guide bar cover 2. Battery cover

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
CAUTION:
Always wear gloves when
performing any inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other
or adjustment should
wobble, resulting
operator. Saw
be cut
it down
weight of the chain
Fig.21
branches, first
shallow
then make
cut from
Fig.22
maintenance
be performed by
22 ENGLISH
Makita Authorized or Factory Service Centers, always
using Makita replacement parts.
Sharpening the saw chain
Sharpen the saw chain when:
•
Mealy sawdust
when damp
cut;
•
The chain penetrates the
with difficulty,
heavy pressure
•
The cutting edge
damaged;
•
The saw pulls
left or
the wood.
sharpening of the saw chain or damage to one
side only)
Sharpen the saw chain frequently but a little each time.
Two or three strokes
file are usually
routine resharpening. When the saw chain has been
resharpened several times, have it sharpened in our
authorized service center.
Sharpening criteria:
WARNING:
An excessive distance between
the cutting edge and depth gauge increases the
risk of kickback.
►
Fig.25: 1. Cutter length 2. Distance
between cutting edge and depth gauge 3.
Minimum cutter length (3 mm)
—
All cutter length must be equal. Different cutter
lengths prevent the saw chain from running
smoothly and may cause the saw chain to break.
—
Do not sharpen the chain when the cutter length
has reached 3 mm or shorter. The chain must be
replaced with new one.
—
The chip thickness is determined by the distance
between the depth gauge (round nose) and the
cutting edge.
—
The best cutting results are obtained with following
distance between cutting edge and depth gauge.
•
Chain blade
0.65 mm
•
Chain blade
0.65 mm
•
Chain blade
0.65 mm
►
Fig.26
— The sharpening angle of 30° must be the same on
all cutters. Different cutter angles cause the chain
to run roughly and unevenly, accelerate wear, and
lead to chain breaks.
—
Use a suitable
so that
sharpening angle is kept against the teeth.
is produced
wood is
wood
even when
is applied;
is obviously
to the
right in
(caused by uneven
with a
sufficient for
90PX :
91PX :
25AP :
round file
the proper