Makita MP100D Betriebsanleitung Seite 9

Lighting up the front lamp
► Fig.6: 1. Lamp 2. Main power switch
CAUTION:
Do not look in the light or see the
source of light directly.
When you turn on the tool by pressing the main power
switch, the lamp lights up. When you turn off the tool by
pressing the main power switch, the lamp goes out.
NOTICE:
When the tool is overheated, the lamp flickers.
Cool down the tool fully before operating the tool again.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Storing adapter
► Fig.7: 1. Sport ball needle 2. Presta valve adapter
3. Adapter holder
The adapters can be stored in the adapter holder of the
tool. Insert the sport ball needle into the Presta valve
adapter before attaching them to the adapter holder.
Storing hose
► Fig.8: 1. Hose holder 2. Hose
The hose can be attached to the hose holder of the tool.
OPERATION
Using the English valve adapter
1. Unfold the air chuck clamp.
2. Insert the English valve adapter into the air chuck.
3. Fold the air chuck clamp firmly.
► Fig.9: 1. English valve adapter 2. Air chuck 3. Air
chuck clamp 4. Valve stem
4. Attach the English valve adapter to the valve stem
while opening the English valve adapter.
5. Turn on the tool.
6. Inflate the tire by pulling the switch trigger while
checking the status of the tire.
NOTICE:
When using the English valve adapter, the
pressure gauge will not display an accurate value
due to characteristics of the valve. When inflating a
tire, do not use the value on the pressure gauge, but
inflate it by checking the status of the tire.
If the tool stops before the tire reaches the
desired air pressure, adjust the pressure value,
and then inflate the tire again.
Using the Schrader valve adapter
1. Unfold the air chuck clamp.
2. Attach the air chuck to the valve stem.
► Fig.10: 1. Air chuck clamp 2. Valve stem 3. Air chuck
3. Fold the air chuck clamp firmly.
4. Turn on the tool, and then set the pressure value
appropriate for the tire using the pressure gauge.
5. Keep pulling the switch trigger until the tool stops.
The tire is inflated with the specified pressure.
Using the Presta valve adapter
1. Loosen the locking nut on the valve stem.
► Fig.11: 1. Locking nut
2. Unfold the air chuck clamp.
3. Attach the Presta valve adapter to the valve stem,
and then attach the air chuck to the Presta valve adapter.
► Fig.12: 1. Presta valve adapter 2. Air chuck 3. Air
chuck clamp 4. Valve stem
4. Fold the air chuck clamp firmly.
5. Turn on the tool, and then set the pressure value
appropriate for the tire using the pressure gauge.
6. Keep pulling the switch trigger until the tool stops.
The tire is inflated with the specified pressure.
7.
Remove the air chuck and Presta valve adapter,
and then tighten the locking nut.
Using the sport ball needle or
tapered adapter
You can inflate small items such as sport balls or float-
ing tubes. To inflate sport balls, use the sport ball nee-
dle. To inflate floating tubes, use the tapered adapter.
1.
Unfold the air chuck clamp.
2. Attach the sport ball needle or tapered adapter to the air chuck.
► Fig.13: 1. Air chuck clamp 2. Air chuck 3. Sport ball
needle 4. Tapered adapter
3. Fold the air chuck clamp firmly.
4. Insert the sport ball needle or tapered adapter into
the hole on the item.
5.
Turn on the tool, and then set the appropriate
pressure value using the pressure gauge.
NOTICE:
When inflating a floating tube, the pressure
gauge will not display an accurate value since the pres-
sure of floating tube is less than 20 kPa. When inflating a
floating tube, do not use the value on the pressure gauge,
but inflate it by checking the status of the floating tube.
6. Keep pulling the switch trigger until the tool stops.
The item is inflated with the specified pressure.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed before
attempting to perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
9 ENGLISH