Operation Instructions; Chlorinator Stationary Mounting Option; Maintenance; Flow Sensor Cleaning - Bestway FLOWCLEAR 58216 Gebrauchsanleitung

Chlorinator

Vorschau ausblenden

Inhaltsverzeichnis

Verfügbare Sprachen

CHLORINATOR STATIONARY MOUNTING (OPTION)

Chlorinators are required to stay in a permanent upright position

according tothe regulations in some areas. In this case, mount the

product to a platform as shown inthe drawings.

Fig. 1

1. Unplug the electrolytic cell line cord. Unscrew the locked nut of the flow

sensor counter-clockwise and disconnect the flow sensor signal line from

the flow sensor. Then screw out the four screws and put aside the

electrolytic cell. (See Fig.1)

2. The mounting holes are 6.4mm in diameter and spaced 180mm apart. Use

two bolts and lock nuts with a maximum of 6.4mm in diameter. And then

reinstall the electrolytic cell and other parts. (See Fig.2)

NOTE: The total assembly must exceed 18kg.

MAINTENANCE

CAUTION: You must ensure the

chlorinator is unplugged before

any maintenance begins or severe

risk of injury or death exists.

Flow Sensor Cleaning

1. Unscrew the lock nut of the flow

sensor, disconnect the signal line,

and remove them from flow sensor.

2. Clean the deposits and debris on

the surface of the flow sensor with

a garden hose. (use a plastic brush if

necessary, but never a metal one) (See Fig. 3)

3. Reinstall the flow sensor signal line, and the lock nut.

NOTE: Do not over tighten.

Electrolytic Cell Cleaning

To extend the life and performance of the electrolytic cells, it is

recommended to inspect it every 3 months and clean it if necessary.

Follow the cleaning instructions below.

1. Turn off the chlorinator and unplug the power cord from the electrical outlet.

2. Remove the debris screens from the inside of the pool and insert the

stopper plugs in the pool's inlet and outlet valves or close the connection

valves.

3. Remove all other components connected to the electrolytic cell and

separate it from the chlorinator.

4. Look inside the electrolytic cell

to inspect for scale formation

(light colored crusty or flaky

deposits). If yes,go to step 5,

otherwise, go to step 6.(See Fig. 4)

5. Try to flush the deposits and debris

with high a pressure garden hose.

Soakthe cell in a vinegar solution

for 2-3 hours if flushing does

not work.

6. Reinstall the electrolytic cell

(Reset the operating time).

NOTE: Do not use any metal tools, they may scratch the coating off the

plates.

NOTE: A buildup on the cell indicates that there is an unusually high

calcium level in the pool. If this is not corrected, you have to frequently

check and clean the cell. To avoid this, always keep your pool chemistry

at the recommended levels. See "Pool Water Chemistry" for reference.

Fig. 2

Fig. 3

Titanium Plates

Fig. 4

STORAGE

1. Unplug the power cord from the electrical outlet.

2. After all water is drained from the pool, disconnect the chlorinator

from the hoses.

3. Air-dry the chlorinator before storage. It is recommended to visually

inspect and clean the electrolytic cell at this time.

4. It is recommended you store the chlorinator in its original package in a

warm dry place.

Bestway

TEST STRIPS (Included in The Package)

Test Strips can test the "Free Chlorine", "PH" and "Total Alkalinity" levels

at the same time. Use as follows.

1. Dip one strip into water, no more than 46cm (18") below the water

surface and remove immediately.

2. Hold strip level for 15 seconds to avoid reactant dripping from one test

pad to another.

NOTE: Do not shake off excess water.

3. Compare results immediately lining up the 3 test pads to the easy color

match chart on the bottle.

TROUBLESHOOTING

Bestway strives to provide the best trouble-free chlorinator on the market.

If you experience any problems, do not hesitate to contact your authorized

dealer or us.

Here are some helpful tips to help you to diagnose and rectify common

sources of trouble.

Problems

Probable Causes

- Insufficient operating time

Insufficient

- Insufficient salt level in

chlorine

pool water

- Chlorine loss due to

intense sunlight

exposure

- The bather load has

increased

- Clogged or dirty

electrolytic cell

- Excessive calcium

White flakes in the

hardness is present in

water

pool water

- No power supply

No LED display

- LED failure

No LED display

- The chlorinator goes is

except that the

in a power saving

LED above the

mode

On-Off Button

displays red

DISPOSAL

Meaning of crossed - out wheeled dustbin:

Do not dispose of electrical appliances as unsorted municipal waste,

use separate collection facilities.

Contact your local government for information regarding the collection

systems available.

If electrical appliances are disposed of in landfills or dumps,

hazardous substances can leak into the groundwater and get into the

food chain, damaging your health and well-being.

When replacing old appliances with new ones, the retailer is legally

obligated to take back your old appliance for disposals at least free of

charge.

Solutions

- Increase the operating time per day.

See "Operation Instructions "

- Test the salt level with test strip, and

adjust as needed. See "Pool Water

Chemistry"

- Use pool cover when the pool is not in use

and/or when the unit is operating

- Increase the operating time per day. See