Bestway FLOWCLEAR 58216 Gebrauchsanleitung Seite 5

For connection to filter pumps with 1-1/4in. (32mm)
(with hose clamps)
Pool
A
B
Connecting Hose
Filter
Pump
For connection to filter pumps / sand filters with 1-1/2in. (38mm)
hose size:
Pool
A
Connecting Hose
Filter Pump
Sand Filter
Adaptor A
OPERATION INSTRUCTIONS
How to Add or Remove Salt?
Adding Salt
1. Switch on the filter to circulate the pool water
2. Keep the chlorinator "OFF".
3. Determine the amount of salt to be added according to the Pool Salt
Usage table.
4. Evenly and slowly pour in the salt around the inside perimeter of the
pool. To avoid clogging the filter, do not add salt through the skimmer.
5. Brush the pool bottom to speed up the dissolving process. Do not
allow salt to pile up on the pool bottom. Run the filter 24 for hours to
dissolve saltcompletely.
6. After 24 hours refer the Flow Status LED Indicator section to
checkwater flow status. If the water flow status is normal, you can
set the chlorinator to the desired operating time.
Removing Salt
If too much salt has been added, the "high" salt level Red LED will light up.
The only way to lower the salt concentration is to drain and refill
approximately 20% of the pool's water until the "high" salt level Red
LED gose out and with the "good" salt level Green LED lights up.
NOTE: After the salt is dissolved, but before
operating the chlorinator be sure that:
• The filter pump/sand filter and the
chlorinator are connected to a grounding
type receptacle protected by a residual
current device (RCD).
• The filter pump/sand filter operates several
minutes before operating the
chlorinator. This removes air pockets and
debris in the water hoses.
• No air is trapped in any of the hoses.
Follow the filter pump/sand filter
manual to release any trapped air.
1. On-off Button
Adaptor E
Adaptor F
B
Adaptor B
Adaptor B
Connecting
Hose
Double
This button turns the chlorinator on and off.
IMPORTANT: Before starting the Flowclear Chlorinator follow the steps
below:
Step 1: First start the filter pump/sand filter pump
Step 2: After chlorinator connect with power outlet, LED light above switch
button shows red. If the LED light shows green or green with twinkle,press
switch button make the LED light turns red.
Step 3: Press the on/off button for 5 seconds then release, after release the
Chlorinator will emit three long beeps
Step 4: on/off button remain red and the chlorinator will be ready to use
Step 5: Wait for 1 minute
Step 6: Push the on/off button the led above become green and the chlorinator
will begin to work. Follow the instruction point 2 for the time adjustment button
NOTE: If after step 6, from the LED above the on/off button flashes green,
repeat the operation again starting from step 2
NOTE:
When the LED on/off button is flashing green and all other LEDs are off,
it means the chlorinatoris in stand-by mode. The chlorinator goes into
stand-by mode after the operation time is completed.
2. Time Adjustment Bottons
Press and hold together the
lock/unlock the keypad. When the keypad is unlocked, the operating time LED
indicators will flash; when the keypad is locked the LED indicator will stop
flashing.
Press the button to increase the operating time 2 hours
Press the button to decrease the operating time 2 hours
NOTE: The unit will automatically lock after no instructions for 5 seconds.
IMPORTANT: When the operating time is set, to change the operation time,
follow the below instructions:
- Push the on/off button for less than one second and the LED will become red
- Follow the instructions in point 1 "on-off button" from step 3
3. Operating Time LED Indicators
The green lights show the remaining hours in the daily operating cycle.
4. Double Time Button
Double
Pressing this button will double the working time shown on the
operating time LED, the LED above
5. Flow Status LED Indicator
Green light indicates there is sufficient water flow turns to produce
chlorine.
Red light indicates insufficient water flow, no chlorine will be
produced.
Note: An alarm, with beeping and a red flashing light, indicating the
insufficient water flow will continue for 5 minutes.
After the 5 minutes, the light will continue flashing, however the beeping will
stop.
After 30 minutes, all lights will turn off
To restart the entire system, press the on/off button for no more than 1 second
6. Salt Level Status LED Indicators
These LED lights indicate the salt level in the pool water.
Red: High. The salt level is too high, no chlorine is produced, salt needs to be
removed from the pool water.
Green: Good. The salt level is optimum, and chlorine is being produced.
Yellow: Low. The salt level is too low, no chlorine is produced, need to
add salt to the pool water.
Note: An alarm, with beeping and a red/yellow flashing light, indicating the
high/low salt level will continue for 5 minutes.
After the 5 minutes, the light will continue flashing, however the beeping will
stop.
After 30 minutes, all lights will turn off
To restart the entire system, press the on/off button for no more than 1 second
NOTE: Refer to the Pool Salt Usage section for salt concentration adjustment.
NOTE: When the chlorinating cycle ends, only the LED above the On-off button
displays flashing green. The chlorinator will go into a standby mode,
and will turn itself back on in 24 hours to continue its daily chlorine production.
IMPORTANT: Never use the pool if chlorine level is more than 3ppm. Do
not operate the chlorinator while the pool is in use or occupied.
• Always use a test trip to test the chlorine level before entering or using the
pool. If the chlorine level is too high, wait until the chlorine level drops below
3ppm before using the pool or operating the chlorinator.
• Heavy pool usage and higher temperatures may require higher chlorine output
(longer operating time) to maintain proper free available chlorine residuals.
• If a power outage occurs or the power cord is unplugged for more than 48
hours, then the chlorinator operating time will have to be reset.
NOTE: LED indicator will not off under sleep mode if it
has been turned in before.
5
and buttons for less than one second to
will light up if in double mode.
Double