Siemens ION PROFIBUS DP Spy T001 Betriebsanleitung (Kompakt

SIPLUS CMS
Industrial I/O-Node
ION PROFIBUS DP Spy T001
6AT8000-1BA00-5XA0
Operating Instructions (Compact)
ION PROFIBUS DP Spy T001
Technical Data
Interfaces
IEEE1394a P1... P3
Number
Connector type
Transfer speed
Power Supply 24 V, 0 V, PD (Power Down)
Connector type
Clamping range
Input voltage
Power loss at 24 V DC
Current consumption at
24 V DC
Fieldbus: PROFIBUS DP
Number
Connector type
Type
Transfer speed
Operation mode
Standard
Ground Connection
Connector type
Clamping range
ION PROFIBUS DP Spy T001
A5E02189686, 03/2009, © SIEMENS AG 2009 Ⓟ 2009
Contact Information
SIEMENS AG
I IA SE DE
Würzburger Str 121
90766 FÜRTH
GERMANY
Customer Support
+49 (0) 180 5050 222
(€ 0.14 /min. from the German landline
network, deviating mobile
communications prices are possible)
Internet
www.siemens.com/siplus-cms
SIEMENS AG
Industry Sector
Postfach 4848
90026 NÜRNBERG
GERMANY
3
6-pin connector
400 Mbps
3-pin connector
(Phoenix Contact)
0.2 ... 2.5 mm²
18 ... 32 V DC
24 W
1 A
1
Sub D socket
PROFIBUS DP
9.6 / 19.2 / 45.45 / 93.75 / 187.5 /
500 kbps
1.5 / 3 / 6 / 12 Mbps
Bus monitor
PROFIBUS DP
M4 screw on the front: SHIELD
Cable socket for screw M4
Scope of delivery
● ION PROFIBUS DP Spy T001
● Operating Manual (compact)
Description
The ION PROFIBUS DP Spy T001 is used to acquire numerical
data and to transmit the recorded data via the FireWire bus
(IEEE1394a-standard) with 400 Mbps to a higher level industrial
PC. The use of an ION PROFIBUS DP Spy T001 allows recording
data which are exchanged between PROFIBUS DP fieldbus nodes.
Assembling
The device must be mounted on a DIN rail. To avoid overheating
the minimum distances specified in the technical data must be
adhered to. Protective equipment and a disconnection unit for the
device must be provided.
Connecting
For clamping ranges: see technical data.
● Screw clamps: Screwdriver with a blade of 3 mm.
Recommended fastening torque: 0.2 ... 0.4 Nm.
● Ground Connection: TX 15 Torx screwdriver.
Recommended tightening torque: approx. 3 Nm.
Commissioning (hardware)
1. Connect the ION with a 24 V power supply. The green PWR
LED of the ION starts to blink.
2. Connect the ION with the PC via an IEEE1394 cable.
3. If the ION is being connected to the PC for the first time,
Windows will request a driver installation. To install the driver,
follow the instructions of the hardware assistant. The directory
for the drive installation is SIPLUS CMS\Drivers\IEEE1394.
4. After Windows has installed a driver for the ION, the ION can
be used with X-Tools. The yellow LNK LED of the ION lights up
and the hardware installation is complete when the ION is
connected to the PC, the driver is installed and X-Tools is
started.
Cables
FireWire
PROFIBUS DP
Environmental Conditions / EMC
Transport and storage
temperature
Ambient temperature during
operation
Humidity rating
EMC interference emission
EMC interference immunity
Degree of protection
Constructive layout
Dimensions (H x W x D) in mm
Minimum distances:
Front
Top
Bottom
Design
Color
Weight
Mounting
Certificates
CE
According to IEEE1394a
standard
According to PROFIBUS DP
standard
- 25 ... + 85 °C
0 ... + 55 °C
5 ... 95 %, non condensing
EN 55011 (class A)
EN 61000-6-2:2005
IP20
200 x 60.2 x 126.5
80 mm
25 mm
25 mm
Aluminum / stainless steel
Silver
1 kg
DIN rail
EN 50022-35x15
thickness 2.3 mm
For use in industrial and office
areas