Maintenance - AEG BBH 12 Originalbetriebsanleitung

TECHNICAL DATA CORDLESS ROTARY HAMMER
Production code............................................................................
Drilling capacity in concrete ..........................................................
Drilling capacity in steel ................................................................
Drilling capacity in wood ...............................................................
No-load speed ..............................................................................
Rate of percussion under load......................................................
Impact energy per stroke according to EPTA-Procedure 05/2009 .....
Chuck neck diameter ....................................................................
Battery ..........................................................................................
Battery voltage..............................................................................
Weight according EPTA-Procedure 01/2003 (1.5 Ah) ..................
Weight according EPTA-Procedure 01/2003 (3.0 Ah) ..................
Noise/Vibration Information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ..........................
Sound power level (Uncertainty K=3dB(A)) ...............................
Wear ear protection!
Total vibration values (vector sum in the three axes) determined
according to EN 60745:
Hammer-drilling in concrete: vibration emission value a
Uncertainty K = ............................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
ROTARY HAMMER SAFETY WARNINGS
Wear ear protectors. Exposure to noise can cause hearing
loss.
Use auxiliary handles supplied with the tool. Loss of control
can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a „live"
wire may make exposed metal parts of the power tool „live" and
could give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Do not machine any materials that present a danger to health
(e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive
force. Determine why the insertion tool stalled and rectify this,
paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
18 ENGLISH
BBH 12
.......................4403 61 03...
...000001-999999
.............................13 mm
...............................8 mm
.............................10 mm
....................... 0-800 min
-1
..................... 0-5350 min
-1
............................0,9 J
.............................43 mm
........................Li-Ion
.............................12 V
............................1,6 kg
............................1,8 kg
..........................85,5 dB (A)
..........................96,5 dB (A)
............ ............................4,4 m/s
2
h
............................1,5 m/s
2
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is
running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household refuse
or by burning them. AEG Distributors off er to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System AEG 18V chargers for charging System AEG
18V battery packs. Do not use battery packs from other
systems.
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fl uid or al-low a fl uid to fl ow inside them.
Corrosive or conductive fl uids, such as seawater, certain
industrial chemicals, and bleach or bleach containing products,
etc., Can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The battery rotary pneumatic hammer can be used for hammer
drilling and drilling in wood, metal as well as plastic for
independent use away from mains supply.
Do not use this product in any other way as stated for normal
use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHs), 2014/30/EU,
2006/42/EC and the following harmonized standards have
been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-6:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015
EN 50581:2012
Winnenden, 2017-07-20
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should
be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure to
heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate for
about 5 seconds, the fuel gauge will fl ash,and then the tool will
turn OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperature of the
battery pack could raise too much. If this happens, the fuel
gauge will fl ash until the battery pack cooled down. After the
lights go off , the work may continue.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties
is subject to Dangerous Goods regulations. Transport
preparation and transport are exclusively to be carried out by
appropriately trained persons and the process has to be
accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice

MAINTENANCE

The ventilation slots of the machine must be kept clear at all
times.
Important note! If the carbon brushes are worn, in addition to
exchanging the brushes the tool should be sent to after-sales
service. This will ensure long service life and top performance.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents (see
our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Please read the instructions carefully before
starting the machine.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
National mark of conformity Ukraine
EurAsian Conformity Mark.
ENGLISH 19