Cap With Grip; Before Starting; Starting; During Operation - hanseatic BHE 3020 Gebrauchsanweisung

ways shut off the engine and allow it to cool before refu-
eling. Gasoline build up inside the fuel tank depending on
the fuel used, the weather conditions and the tank venting
system.
In order to reduce the risk of burns and other personal
injury from escaping gas vapor and fumes, remove the
fuel filler cap on your engine allow any pressure build-up
in the tank to release slowly. Never remove the fuel filler
cap while the engine is running. Select bare ground for
fueling and move at least 10 feet (3 m) from the
fueling spot before starting the engine. Wipe off any
spilled fuel before starting your machine.
! Warning!
Check for fuel leakage while refueling and during opera-
tion. If fuel leakage is found, do not start or run the en-
gine until the leak is fixed and any spilled fuel has been
wiped away. Take care not to get fuel onyour clothing. If
this happens, change your clothing immediately. Different
models may be equipped with different fuel caps.

Cap with grip

! Warning!
In order to reduce the risk of fuel spillage and fire from
an improperly tightened fuel cap, correctly position and
tighten the fuel cap in the fuel tank opening.
Screw cap
! Warning!

Before Starting

! Warning!
Always check your engine for proper condition and op-
eration before starting, particularly the throttle trigger,
throttle trigger interlock, stop switch and working tool.
The throttle trigger (if applicable) must move freely and
always spring back to the idle position. Never attempt to
modify the controls or safety devices.
! Warning!
Never use a power tool that is damaged or not properly
maintained.
Check that the spark plug boot is securely mounted on
the spark plug loose boot may cause arcing that could
ignite combustible fumes and cause a fire. Keep the han-
dles clean and dry at all times; it is particularly important
to keep them free of moisture, pitch, oil, grease or resin in
order for you to maintain a firm grip and properly control
your engine.

Starting

Start the engine at least 10 feet (3 meters) from the
fueling spot, outdoors only.
Place the power tool on firm ground or other solid sur-
face in an open area. Maintain good balance and secure
footing.
Downloaded from www.Manualslib.com
Unit vibrations can cause an improperly
tightened fuel filler cap to loosen or come
off and spill quantities of fuel.
In order to reduce the risk of fuel spillage
and fire, tighten the fuel filler cap by hand
as securely as possible.
manuals search engine
! Warning!
Your engine is a one-person machine. Do not allow other
persons in the general work area, even when starting.
To reduce the risk of injury from loss of control, do not
attempt to "drop start" your power tool.
When you pull the starter grip, do not wrap the starter
rope around your hand. Do not let the grip snap back,
but guide the starter rope to rewind it properly. Failure to
follow this procedure may result in injury to your hand or
fingers and may damage the starter mechanism.
Important Adjustments
! Warning!
To reduce the risk of personal injury from loss of control or
contact with the running working tool, do not use a power
tool with incorrect idle adjustment. At correct idle speed,
the working tool should not move.

During Operation

Holding and controlling the power tool
Always hold the unit firmly with both hands on the
handles while you are working. Wrap your fingers and
thumbs around the handles.
Your right hand should grip the rear handle. This also ap-
plies to left-handers.
Working conditions
Operate and start your power tool only outdoors in a well
ventilated area. Operate it under good visibility and day-
light conditions only. Work carefully.
! Warning!
As soon as the engine is running, this prod-
uct generates toxic exhaust fumes containing
chemicals (such as unburned hydrocarbons and
carbon monoxide) known to cause respiratory
problems, cancer, birth defects, or other repro-
ductive harm. Some of the gases (e.g. carbon
monoxide) may be colorless and odorless. To
reduce the risk of serious or fatal injury/illness
from inhaling toxic fumes, never run the ma-
chine indoors or in poorly ventilated locations.
The muffler and other parts of the engine (e.g. fins of the
cylinder, spark plug) become hot during operation and re-
main hot for a while after stopping the engine.
To reduce risk of burns do not touch the muffler and other
parts while they are hot.
To reduce the risk of fire and burn injury, keep the area
around the muffler clean. Remove excess lubricant and
all debris such as pine needles, branches or leaves. Let
GB-4