IGM LAGUNA PFlux 3 Gebrauchsanweisung Seite 13

Step 43: Apply foam tape to the hole on the dust chute before securing
the pressure switch using (4) M4*12MM sheet metal thread bolts.
Step 44: Locate the D1-1/4"*230mm black flex hose and two D1-1/4"
hose clamps in the hardware box. Connect the one end of the flex hose Step Forty Four: Locate the Ø1-1/4"*230mm black flex hose and two Ø1-1/4"
to the vacuum suction tube which is located on the top end of the cyclone
hose clamps in the hardware box. Connect the one end of the flex hose to the
cone. Connect the other end of the flex hose to the octagon drum lid
vacuum suction tube which is located on the top end of the cyclone cone.
vacuum tube which is located on the back end of the drum lid closest to
Connect the other end of the flex hose to the octagon drum lid vacuum tube
the canister filter. Secure both ends with the hose clamps provided.
which is located on the back end of the drum lid closest to the canister filter.
Secure both ends with the hose clamps provided.
Cyclone Cone vacuum suction tube
Step Forty Five: If you do not want to use a plastic bag inside the octagon
Step 45: If you do not want to use a plastic bag inside the octagon
collection drum, you need to block off the negative pressure. There is a little pack
collection drum, you need to block off the negative pressure. There is a
containing the items needed to do this. You will also need take the (4)
little pack containing the items needed to do this. You will also need take
carriage bolts, (4) 1/4"*OD19*2t flat washers and (4) 1/4" hex nuts that were
the (4) 1/4"*1/2" carriage bolts, (4) 1/4"*OD19*2t flat washers and (4) 1/4"
securing the vacuum suction pipe to assemble the cover plates. The vacuum
hex nuts that were securing the vacuum suction pipe to assemble the
suction pipe on the drum will be removed for this. It will not have a purpose if you
cover plates. The vacuum suction pipe on the drum will be removed for
block off the negative pressure.
this. It will not have a purpose if you block off the negative pressure.
Plug
www.igmtools.com
3HP Mobile Dust Cyclone Manual
Pic. 46
Pic. 47
Pic. 48 Drum lid vacuum suction tube
Cover plates
Foam tape
securing the vacuum suction pipe to assemble the cover plates. The vacuum
suction pipe on the drum will be removed for this. It will not have a purpose if you
block off the negative pressure.
Plug
Step 46: Remove the vacuum suction pipe from the drum by loosening the
(4) 1/4"*1/2" carriage bolts, (4) 1/4"*OD19*2t flat washers and (4) 1/4" hex
Step Forty Six: Remove the vacuum suction pipe from the drum by loosening the
nuts mentioned in the previous step. There will be 2 sets from the top and
(4)
1/4"*1/2" carriage bolts, (4) 1/4"*OD19*2t flat washers and (4) 1/4" hex nuts
2 sets from the bottom of the vacuum suction pipe.
mentioned in the previous step. There will be 2 sets from the top and 2 sets from
the bottom of the vacuum suction pipe.
Step 47: Take the one of the cover plates, (2) 1/4"*1/2" carriage bolts,
Step Forty Seven: Take the one of the cover plates, (2)
(2) 1/4"*OD19*2t flat washers and (2) 1/4" hex nuts and secure the cover
(2) 1/4"*OD19*2t flat washers and (2) 1/4" hex nuts and secure the cover plate to
plate to the opening on the top of the drum. For the bottom holes do the
the opening on the top of the drum. For the bottom holes do the same, but first
same, but first use foam tape to cover the square opening before bolting
use foam tape to cover the square opening before bolting on the cover plate.
on the cover plate.
Step 48: Remove the flex hose and clamps from the cyclone cone in
step forty one. Locate the plug provided inside the hardware box and
1/4"*1/2"
attach over the vacuum suction tube as shown in the picture on the right
below.
-13-
36
Cover plates
Cover plates
Foam tape
Foam tape
Plug
3HP Mobile Dust Cyclone Manual
Pic. 49
Pic. 50
Cover plates
Cover plates
Pic. 51
3HP Mobile Dust Cyclone Manual
36
1/4"*1/2" carriage bolts,