Using The Appliance; Operating Modes - Clatronic CL 3750 Bedienungsanleitung, Garantie

Using the Appliance

• Settings made via the appliance are not transmitted to the remote
control.
• As soon as you press a button on the remote control, the appliance will
apply the corresponding settings from the remote control.
• Your selection will appear on the display of the remote control.
• The and buttons must be pressed several times to select the
individual functions.
The buttons on the control panel are explained below. The indicator lights
show your chosen selection.

Operating Modes

Use the MODE button to select one of the following operating modes:
• Cooling COOL
• Dehumidifying DRY
• Fan FAN
Operating Mode "Cooling"
In this operation mode, you can adjust the fan speed and the temperature
as desired.
NOTE:
To operate the appliance with the compressor, the set temperature must
be lower than the current room temperature.
Operating Mode "Fan"
This mode only allows you to set the speed of the fan.
Operating Mode "Dehumidifying"
• This operating mode does not support any further settings.
• The fan speed is preset to the lowest level LOW.
• The appliance will cool the room and extract the humidity from the air.
• When using the mode "Dehumidifying" over an extended period, we
recommend permanently connecting the supplied water hose to the
upper water drain (see figure). Remove the top plug first. Place the end
of the water hose in a container of sufficient size (e. g. a bucket).
Setting the Fan
In "Cooling" and "Fan" modes you can set the fan speed with 3 different
settings. Press the FAN SPEED button accordingly.
• LOW (low)
• MEDIUM (medium)
• HIGH (high)
Setting the Temperature
• Use the or buttons in "Cooling" mode to set the temperature.
• Select a temperature between 16 °C (61 °F) and 31 °C (88 °F).
NOTE:
Switching between °celsius and °fahrenheit is only possible using the
button on the remote control.
CL3750_IM_neu
"Sleep Mode"
• Press the SLEEP button when the appliance is switched on and in the
"Cooling" operating mode.
• The fan speed is preset to the lowest level LOW. This cannot be
changed.
• The display will switch off after 10 seconds.
• After running for one hour in the "Sleep" mode, the preset temperature
will automatically increase by 1° C. This will be repeated one hour later
again. This way, a comfortable room temperature will be achieved.
Setting the Air Outlet
Use the button to set the direction of the airflow being emitted.
• Press the button multiple times until the pivoting flap is set into the
desired position.
Timer (Automatic Timer)
Use the timer function to set the power-on and power-off times of the
appliance. Select a time between 1 and 24 hours.
Using the Timer Function for Automatic Power-On
1. Press the POWER button to turn on the appliance.
2. Select the operating mode, temperature and fan speed for the appli-
ance to operate in or at when powered on at the pre-set time.
3. Press the POWER button to turn off the appliance.
4. Press the button. The number of hours flashes.
5. You can set the desired number of hours with the buttons
The setting mode is automatically exited after approx. 5 seconds. Timer
operation is activated and the TIMER indicator light illuminates.
NOTE:
Do not press the button after setting the hours, as the timer
operation will not be saved.
Using the Timer Function for Automatic Power-Off
1. Press the POWER button to turn on the appliance.
2. Press the button during operation. The number of hours flashes.
3. Set the timer as described in the above item 5.
NOTE:
• If you want to deactivate the set timer operation, press the
twice. The TIMER indicator light goes off.
• You may also cancel the timer function at any time by pressing the
POWER button to turn the appliance on / off.
MIRAGE Button
Press the MIRAGE button to switch the display located in the front of the
appliance on or off.
Emptying the Water Tank
The appliance integrates a water tank for collecting condensation. When
the water tank is full, the pilot lamp
ance switches off.
CAUTION:
Do not transport the appliance while the water tank is full. Water could
get into the appliance.
In order to continue operation, you need to empty the water tank. For this,
you need a floor cloth, a flat bowl with a capacity for approx. 0.5 litre of
water and the water hose supplied with the appliance.
1. Disconnect the mains plug from the wall socket.
2. Place the floor towel and the flat bowl underneath the water outlet. If
possible, set the bowl on a lower level than the appliance.
3. Remove the bottom plug.
4. Connect the water hose to the water outlet of the appliance. Place the
end of the hose in the bowl.
5. After the water has been discharged, remove the water hose. Use the
stopper to close the water drain on the appliance again.
and .
button
BUCKET FULL lights up. The appli-
45
18.12.2019