Kinderkraft VEO Bedienungsanleitung Seite 36

NOTE! Before using the wheelchair, make sure that all the
wheels are properly installed.
IV USE OF BRAKE
The buggy is equipped with a foot brake located on the rear axle. Press the brake pedal down (FIG. 8A) to activate it. The
brake is released after the pedal is lifted up (FIG. 8B).
V ASSEMBLY/DISASSEMBLY OF BASSINET AND SAFETY BAR
Place the bassinet on a flat surface. Press buttons for footrest adjustment to unfold the bassinet (FIG. 9). The footrest
may be adjusted using these buttons. Before mounting the bassinet onto the frame, attach the Velcro fasteners to the
metal bar underneath the bassinet (FIG. 10) i and leave it unfolded (FIG. 11). When installing the bassinet on the buggy
frame, place it onto the openings (FIG. 12) designed for this purpose on each side of the buggy until you hear clicking
sound.
NOTE! THE BASSINET CAN ONLY BE MOUNTED FACING
BACKWARDS (the child faces the person pushing the buggy).
The safety bar should be inserted into the special openings in the frame on each side of the buggy, until you hear the
clicking sound (FIG. 13).
VI ATTACHING THE FOOTMUFF AND SUNSHADE
Attach the footmuff (part I) using the zipper located on the inner side of the seat / bassinet. Fasten the zipper (FIG. 14)
and secure the Velcro fastener of the footmuff onto the safety bar. Fasten the zipper of the sunshade around the inner
side of the seat / bassinet (FIG. 16). Close the clamps on the frame to insert the pins into the openings (FIG. 15). The
sunshade may be extended to cover a larger part of the bassinet and seat. For this purpose, open the zipper located on
the outer side of the sunshade lining (FIG. 17) and unfold the sunshade. NOTE! Correctly unfolded buggy with attached
bassinet is shown in FIG. 18.
VII CONVERTING THE BASSINET INTO THE SEAT
In order to convert the bassinet function into the stroller, remove the bassinet part from the frame. Then fasten together
the two clamps under the seat (FIG. 19 and FIG. 20) and mount the seat again the on the frame. Next, adjust the backrest
to the seating position, using the strap behind the backrest (FIG. 21). The seat has 4 positions: lying, 2 x reclining and
sitting - they are adjusted by a lever that is located in the seat frame (FIG. 22) and a strap behind the backrest.
VIII SAFETY HARNESS
Press the button to open the clamp (FIG. 23A). To secure the child, connect the fasteners of hip and shoulder straps and
then insert them into the middle clamp (FIG. 23B) until it engages. Adjust the safety harness each time you fasten (FIG.
23C), to properly secure the child. If your child cannot independently sit up, roll over or push itself up on its hands and
knees inside the bassinet, you don't have to use the harness. Lock all harness straps into the buckle and cover the harness
with mattress. Removing the harness (for cleaning): Remove shoulder and hip straps out of openings (FIG. 24A) by pushing
plastic tabs inside. The assembly is performed in reverse order (FIG. 24B). After completing the assembly, make sure that
the plastic tabs firmly secure the straps.
IX ADJUSTING SHOCK-ABSORBING FUNCTION and TELESCOPIC HANDLE
The buggy has a two-stage adjustable shock-absorbing function. The adjustment levers are located on the bottom side of
the rear axle with brake, next to the basket (FIG. 25). For driving on uneven surfaces firmly, pull firmly the lever toward
the rear axle, until it locks (FIG. 26). In this position, the shock absorbers will cushion all inequalities. For driving on flat
surfaces firmly pull the button in the opposite direction until it engages (FIG. 27). In this position the shock absorbers will
provide greater stability. To adjust the length of the telescopic handle, push the button in its centre and pull it out or push
it in (FIG. 33).
X ASSEMBLING THE CAR SEAT ON THE BUGGY FRAME
The supplied adapters are compatible with the following car seats: Kinderkraft, Maxi Cosi®, Cybex® and are suitable for
the following models: Kinderkraft MINK, Cybex Aton, Aton 2, Aton Q i Maxi Cosi Mico, Mico AP, Mico NXT, Mico Max 30,
Citi, Cabrio, and CabrioFix. Place adapters in the openings on both sides of the seat until you hear the lock clicks (FIG. 28).
When installing the car seat on the buggy frame, push it into the openings on each side of the frame, until you hear
clicking sound of engaged lock (FIG. 29). To remove the seat from the frame, pull the lever of the adapters on both sides
of the buggy (FIG 30) and remove the seat. NOTE! The seat must be always installed on the frame with child's back to
the direction of travel (the child should face the person pushing the buggy) (FIG 31). To remove the adapters push the
buttons on both sides of the seat (FIG. 32).
XI DISASSEMBLING THE BUGGY
Adjust the handle to the lowest position and remove the seat / bassinet from the frame (FIG. 33).
36