Declaration Of Conformity - Bosch GSK 64 Originalbetriebsanleitung

OBJ_BUCH-1039-002.book Page 22 Thursday, January 14, 2010 6:17 PM
22 | English

Declaration of Conformity

We declare under our sole responsibility that the product
described under "Technical data" is in conformity with
the following standards or standardization documents:
EN 792 according to the provisions of the directives
98/37/EC (until 28 Dec 2009), 2006/42/EC (from
29 Dec 2009).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 07.12.2009
Assembly
Connecting the Air Supply (see figure A)
Make sure that the pressure of the compressed-air sys-
tem is below the maximum permitted rated pressure of
the pneumatic tool. Firstly, set the air pressure to the
lower value of the recommended rated pressure (see
"Technical Data").
When in doubt, check the pressure at the air inlet with a
pressure gauge with the pneumatic tool switched on.
For maximum performance, the values for the supply-air
hose 17 (connection thread, maximum operating pres-
sure, inner hose diameter, maximum hose length; see
"Technical Data") must be observed.
The compressed air supplied should be free of foreign
material and moisture to protect the tool from damage,
contamination, and the formation of rust.
All fittings, connecting lines and hoses must be dimen-
sioned for the pressure and the required air volume.
Avoid restrictions in the air supply, e.g., from pinching,
kinking, or stretching!
1 609 929 U14 | (14.1.10)
Downloaded from www.Manualslib.com
Dr. Eckerhard Strötgen
Head of Product
Certification
manuals search engine
Connecting the Air Supply to the Pneumatic Tool
– Empty the magazine 11.
(See "Emptying the Magazine", page 24)
For the following worksteps, a fastener can be dis-
charged when interior parts of the pneumatic tool are
not in the starting position due to repairs, maintenance
or transport.
– Connect the air connector 8 with a supply-air hose 17
equipped with an air-connection coupling 16.
– Check the proper function by placing the outlet 15 or
the rubber workpiece protector 1 of the pneumatic
tool onto a piece of scrap wood or wood material, and
discharging once or twice.
Loading the Magazine (see figures B1
Disconnect the air supply before making any
adjustments, changing accessories, or plac-
ing the pneumatic tool aside. This safety
measure prevents accidental starting of the
pneumatic tool.
¢ Use only original Bosch accessories (see "Technical
Data"). The precision parts of the pneumatic tool such
as the magazine, the outlet and the shot duct are
matched to Bosch staples, nails and brads. Other man-
ufacturers use other steel qualities and sizes.
Using fasteners not permitted, can damage the pneu-
matic tool and cause injuries.
While loading the magazine, hold the pneumatic tool in
such a manner that the outlet 15 is not pointed at your
own body or at other persons.
– Clean and lubricate the magazine slider 12 as required
and make sure that the magazine 11 is not dirty/soiled.
– Insert a fitting nail strip 18 in the T-slot at the end of
the magazine 11.
– Push the nail strip in the magazine toward the front un-
til the last nail is positioned in front of the magazine
spring 10.
Note: A lock function of the magazine slider prevents the
pneumatic tool from being started with an empty maga-
zine. The discharge lock-off cannot be pressed in and
blank firing is thus prevented.
– Press the pretensioned nail pusher 13 against the mag-
azine slider 12 and at the same time, pull the magazine
slider completely to the end of the magazine 11.
Note: The magazine slider must slide back with only low
force (finger-pressure). A tight-running magazine slider
causes the nails to be driven in at an incorrect angle.
B4)
–
Bosch Power Tools