Machine-Specific Safety Warnings - Bosch PST 700 PE Bedienungsanleitung

OBJ_BUCH-250-001.book Page 16 Monday, August 14, 2006 10:17 AM
d) Store idle power tools out of the reach of
e) Maintain power tools. Check for misalign-
f) Keep cutting tools sharp and clean. Prop-
g) Use the power tool, accessories and tool
5) Service
a) Have your power tool serviced by a quali-
Machine-specific
Safety Warnings
Instructions for Jigsaws
Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
Do not work materials containing asbestos.
Asbestos is considered carcinogenic.
Take protective measures when dust can
develop during working that is harmful to
one's health, combustible or explosive. Exam-
ple: Some dusts are regarded as carcinogenic.
Wear a dust mask and work with dust/chip extrac-
tion when connectable.
Keep your workplace clean. Blends of materials
are particularly dangerous. Dust from light alloys
can burn or explode.
Always wait until the machine has come to a
complete stop before placing it down. The tool
insert can jam and lead to loss of control over the
power tool.
16 | English
Downloaded from www.Manualslib.com
children and do not allow persons unfamil-
iar with the power tool or these instruc-
tions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
ment or binding of moving parts, breakage
of parts and any other condition that may
affect the power tool's operation. If dam-
aged, have the power tool repaired before
use. Many accidents are caused by poorly main-
tained power tools.
erly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
bits etc. in accordance with these instruc-
tions, taking into account the working con-
ditions and the work to be performed. Use
of the power tool for operations different from
those intended could result in a hazardous situ-
ation.
fied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
manuals search engine
Never use the machine with a damaged cable.
Do not touch the damaged cable and pull the
mains plug when the cable is damaged while
working. Damaged cables increase the risk of an
electric shock.
Connect machines that are used in the open
via a residual current device (RCD).
Keep hands away from the sawing range. Do
not reach under the workpiece. Contact with
the saw blade can lead to injuries.
Apply the machine to the workpiece only
when switched on. Otherwise there is danger of
kickback when the cutting tool jams in the work-
piece.
Pay attention that the base plate 7 rests
securely on the material while sawing. A
jammed saw blade can break or lead to kickback.
When the cut is completed, switch off the
machine and then pull the saw blade out of
the cut only after it has come to a standstill. In
this manner you can avoid kickback and can place
down the machine securely.
Use only sharp, flawless saw blades. Bent or
unsharp saw blades can break or cause kickback.
Do not brake the saw blade to a stop by apply-
ing side pressure after switching off. The saw
blade can be damaged, break or cause kickback.
Use suitable detectors to determine if utility
lines are hidden in the work area or call the
local utility company for assistance. Contact
with electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Pene-
trating a water line causes property damage or may
cause an electric shock.
Instructions for Machines with Laser
(PST 800 PEL/PST 900 PEL)
Never make warning signs on the machine
unrecognisable.
Laser radiation class 2M
Do not stare into the laser beam
yourself or view directly at it with
optical instruments.
Do not direct the laser beam at per-
sons or animals and do not stare
into the laser beam yourself. This
power tool produces laser class 2M
laser radiation
EN 60825-1. A direct look into the laser
beam, especially with optically converging instruments
such as binoculars etc., can cause damage to the eye.
according to IEC
2 609 932 567 • 14.8.06