Identity Card - Newtec NT06 Informationsblatt

condition and operates correctly.
- During pre-use check it is necessary to inspect all elements of the equipment in respect of any damages, excessive
wear, corrosion, abrasion, cutting or incorrect acting, especially take into consideration: in full body harnesses and belts:
buckles, adjusting elements, attaching points, webbings, seams, loops; in energy absorbers: attaching loops, webbing,
seams, connectors; in textile lanyards or lifelines or guidelines: rope, loops, thimbles, connectors, adjusting element,
splices; in steel lanyards or lifelines or guidelines: cable, wires, clips, ferrules, loops, thimbles, connectors, adjusting
elements; in retractable fall arresters: cable or webbing, retractor and brake proper acting, casing, energy absorber,
connector; in guided type fall arresters: body of the fall arrester, sliding function, locking gear acting, rivets and screws,
connector, energy absorber; in connectors: main body, rivets, gate, locking gear acting
- It is essential for the safety of the user that if the product is re-sold outside the original country of destination the reseller
shall provide instructions for use, for maintenance, for periodic examination and for repair in language of the country in
which the product is to be used.
- A full body harness conformed to EN 361 is the only acceptable body holding device that can be used in a fall arrest
system.
- In full body harness use only attaching points marked with big letter "A" to attach a fall arrest system. Marking like "A/2"
or a half of "A" means the necessity of attaching a fall arrest system to both attaching points together simultaneously. It is
strictly forbidden to attach a fall arrest system to the single attaching point marked "A/2" or a half of "A".
- There are many hazards that may affect the performance of the equipment and corresponding safety precautions that
have to be observed during equipment utilization, especially: trailing or looping of lanyards or lifelines over sharp edges;
any defects like cutting, abrasion, corrosion; climatic exposure; pendulum falls; extremes of temperature; chemical
reagents; electrical conductivity.
- PPE can be cleaned without causing adverse effect on the materials in the manufacture of the
equipment. For textile products use mild detergents for delicate fabrics, wash by hand or in a machine and rinse in water.
Plastic parts can be cleaned only with water. When the equipment becomes wet, either from being in use or when due
cleaning, it shall be allowed to dry naturally, and shall be kept away from direct heat. In metallic products some mechanic
parts (spring, pin, hinge, etc.) can be regularly slightly lubricated to ensure better operation. Other maintenance and
cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.
- PPE must be transported in its original package.
- PPE must be stored in their original packaging, in a well-ventilated place, protected from direct light, ultraviolet
degradation, damp environment, sharp edges, extreme temperatures and corrosive substances.
- The PPE must be disposed of in compliance with the local regulations in force on this subject (dump, incinerator).
- In the case of manufacturing defects this PPE will be replaced.
It is the responsibility of the user organisation to provide the IDENTITY CARD and to fill in the details required. The identity
card should be filled in before the first use of the equipment. Any information about the protective equipment (device name,
serial number, date of purchase, date of first use, user's name, information about reviews and repairs) shall be noted in the
IDENTITY CARD. Do not use the PPE without the identity card duly filled in.
DEVICE NAME
SERIAL NUMBER
USER'S NAME
DATE OF PURCHASE
DATE INSPECTION REASON
1
2
3
4
5

IDENTITY CARD

TECHNICAL INSPECTIONS
For more information, contact:
Registered Community Trade Mark, no 001240407 c/o UAMI - Alicante - Spagna
www.newtecsafety.com - info@newtecsafety.com - Factory: PL8310001653
CODE
PRODUCTION DATE
DATE OF FIRST USE
DEFECTS NOTED, REPAIRS CARRIED OUT,
OTHER RELEVANT INFORMATION
cod.121034 - mod. NT06
RESPONSIBLE
PERIODIC REVIEW NEXT
DUE DATE
SIGNATURE
PERSON