Functional Description - Berner 000088 Originalbetriebsanleitung

Vorschau ausblenden

Inhalt

Seite von 87

/ 87
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

OBJ_BUCH-1135-001.book Page 14 Tuesday, January 12, 2010 1:32 PM

d) Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, break-

age of parts and any other condition that

may affect the power tool's operation. If

damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Prop-

erly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool

bits etc. in accordance with these instruc-

tions, taking into account the working

conditions and the work to be performed.

Use of the power tool for operations different

from those intended could result in a hazardous

situation.

5) Service

a) Have your power tool serviced by a quali-

fied repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Planer Safety Rules

¢ Wait for the cutter to stop before setting the

tool down. An exposed cutter may engage the

surface leading to possible loss of control and seri-

ous injury.

¢ Hold the power tool by insulated gripping

surfaces only, because the cutter may con-

tact its own cord. Cutting a "live" wire may make

exposed metal parts of the power tool "live" and

could give the operator an electric shock.

¢ Use clamps or another practical way to

secure and support the workpiece to a stable

platform. Holding the work by your hand or

against the body leaves it unstable and may lead to

loss of control.

¢ Use suitable detectors to determine if utility

lines are hidden in the work area or call the

local utility company for assistance. Contact

with electric lines can lead to fire and electric

shock. Damaging a gas line can lead to explosion.

Penetrating a water line causes property damage

or may cause an electric shock.

¢ Do not reach into the saw dust ejector with

your hands. They could be injured by rotating

parts.

14 | English

¢ Apply the machine to the workpiece only

when switched on. Otherwise there is danger of

kickback when the cutting tool jams in the work-

piece.

¢ When working, always hold the planer in

such a manner that the planer base plate

faces flat on the workpiece. Otherwise the

planer can become wedged and lead to injuries.

¢ Never plane over metal objects, nails or

screws. The planer blade and the blade shaft can

become damaged and lead to increased vibra-

tions.

¢ Secure the workpiece. A workpiece clamped

with clamping devices or in a vice is held more

secure than by hand.

¢ Never use the machine with a damaged

cable. Do not touch the damaged cable and

pull the mains plug when the cable is dam-

aged while working. Damaged cables increase

the risk of an electric shock.

Products sold in GB only: Your product is fitted

with an BS 1363/A approved electric plug with inter-

nal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it

should be cut off and an appropriate plug fitted in its

place by an authorised customer service agent. The

replacement plug should have the same fuse rating as

the original plug.

The severed plug must be disposed of to avoid a pos-

sible shock hazard and should never be inserted into

a mains socket elsewhere.

Products sold in AUS and NZ only: Use a residual

current device (RCD) with a rated residual current of

30 mA or less.