Declaration Of Conformity; Changing The Tool; Dust/Chip Extraction - Berner 000088 Originalbetriebsanleitung

OBJ_BUCH-1135-001.book Page 16 Tuesday, January 12, 2010 1:32 PM

Declaration of Conformity

We declare under our sole responsibility that the
product described under "Technical Data" is in con-
formity with the following standards or standardization
documents: EN 60745 according to the provisions of
the directives 2004/108/EC, 2006/42/EC.
Technical file at:
Berner GmbH, Berner Str. 6, D-74653 Künzelsau
Künzelsau, 12.10.2009
Jörn Werner Ulrich Lindner
CEO COO
12.10.2009, Berner GmbH; Bernerstraße 6;
D-74653 Künzelsau
Assembly
¢ Before any work on the machine itself, pull
the mains plug.

Changing the Tool

¢ Be cautious when replacing the planer
blades. Do not grasp the planer blades by
the cutting edges. Possible danger of injury due
to the sharp cutting edges of the planer blades.
Use only original Berner carbide blades (TC).
The carbide blade (TC) has 2 cutting edges and can
be reversed. When both cutting edges are dull, the
planer blade 16 must be replaced. The carbide blade
(TC) may not be resharpened.
Disassembling the Planer Blade(s)
(see figure A)
To reverse or replace the planer blade 16, rotate the
blade drum 13 until it is parallel to the planer base
plate 10.
‹ Loosen the two fastening screws 15 with the
Allen key 18 by approx. 1 – 2 turns.
› If necessary, loosen the clamping element 14 by
giving it a light blow with a suitable tool (e.g. a
wooden wedge).
fi Fold the lateral blade-shaft protector 17 down
and push the carbide blade 16 sideward out of
the blade drum 13 using a piece of wood.
16 | English
Assembling the Planer Blade(s) (see figure B)
The guide groove of the planer blade always ensures
continuous height adjustment when replacing or
reversing it.
If required, clean the blade seat in the clamping ele-
ment 14 and the planer blade 16.
When assembling the planer blade, ensure that it is
seated properly in the blade holder of the clamping
element 14 and aligned flush at the side edge of the
rear planer base plate 10. Afterwards tighten the
2 fastening screws 15 again with the Allen key 18.
Note: Before restarting, check if the fastening screws
15 are tightened well. Rotate the blade drum 13 by
hand and ensure that the planer blade does not graze.

Dust/Chip Extraction

¢ Dusts from materials such as lead-containing coat-
ings, some wood types, minerals and metal can be
harmful to one's health. Touching or breathing-in
the dusts can cause allergic reactions and/or lead
to respiratory infections of the user or bystanders.
Certain dusts, such as oak or beech dust, are con-
sidered as carcinogenic, especially in connection
with wood-treatment additives (chromate, wood
preservative). Materials containing asbestos may
only be worked by specialists.
– Use dust extraction whenever possible.
– Provide for good ventilation of the working
place.
– It is recommended to wear a P2 filter-class res-
pirator.
Observe the relevant regulations in your country
for the materials to be worked.
Clean the chip ejector 2 regularly. Use a suitable tool
(e.g., a piece of wood, compressed air, etc.) to clean
a clogged chip ejector.
¢ Do not reach into the saw dust ejector with
your hands. They could be injured by rotating
parts.
To ensure optimum extraction of dust/chips, always
work with external dust extraction or a chip/dust bag.
External Dust Extraction (see figure C)
An extraction hose ( Ø 35 mm) 19 (accessory), can be
attached on either side of the chip ejector.
Connect the vacuum hose 19 to a vacuum cleaner
(accessory). An overview for connecting to various
vacuum cleaners can be found at the end of this man-
ual.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimen-
tal to health or carcinogenic, use a special vacuum
cleaner.
2 609 932 749 • 12.1.10