Safety Instructions For Planers; Product Description And Specifications; Intended Use; Product Features - Berner BP 40-82 C Originalbetriebsanleitung

ures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of chil-
u
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous
in the hands of untrained users.
Maintain power tools and accessories. Check
u
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired be-
fore use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
u
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool bits
u
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Keep handles and grasping surfaces dry,
u
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unex-
pected situations.
Service
English
Have your power tool serviced by a qualified
u
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.

Safety instructions for planers

Wait for the cutter to stop before setting the
u
tool down. An exposed rotating cutter may en-
gage the surface leading to possible loss of
control and serious injury.
Hold the power tool by insulated gripping sur-
u
faces, because the cutter may contact its
own cord. Cutting a "live" wire may make ex-
posed metal parts of the power tool "live" and
could give the operator an electric shock.
Use clamps or another practical way to se-
u
cure and support the workpiece to a stable
platform. Holding the workpiece by your hand
or against the body leaves it unstable and may
lead to loss of control.
Only bring the power tool into contact with
u
the workpiece when switched on. Otherwise
there is danger of kickback if the cutting tool
jams in the workpiece.
Do not allow the chip ejector to come into
u
contact with your hands. You may be injured
by rotating parts.
1 609 92A 4LM • 1.3.19
Never plane over metal objects, nails or
u
screws. Cutters and cutter shafts could be-
come damaged and cause increased vibration.
Use suitable detectors to determine if utility
u
lines are hidden in the work area or call the
local utility company for assistance. Contact
with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property
damage or may cause an electric shock.
While working, always hold the planer in such
u
a way that the planer base plate lies flat
against the workpiece. Otherwise the planer
could slip and cause injury.
Products sold in GB only:
Your product is fitted with an BS 1363/A ap-
proved electric plug with internal fuse (ASTA ap-
proved to BS 1362).
If the plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in
its place by an authorised customer service agent.
The replacement plug should have the same fuse
rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inser-
ted into a mains socket elsewhere.
Hold the power tool firmly with both hands
u
and make sure you have a stable footing. The
power tool can be more securely guided with
both hands.
Product Description and
Specifications
English
Please observe the illustrations at the beginning
of this operating manual.

Intended use

The power tool is intended for planing wood-
based materials such as beams and boards while
resting firmly on the workpiece. It is also suitable
for chamfering edges and for rebating.

Product features

The numbering of the product features refers to
the diagram of the power tool on the graphics
page.
(1) Knob for setting the cutting depth (insulated
gripping surface)
(2) Chip ejector (either right or left)
English
Read all the safety and general in-
structions. Failure to observe the
safety and general instructions may
result in electric shock, fire and/or ser-
ious injury.
English
English
English | 13