Herunterladen Inhalt Inhalt Diese Seite drucken

Kity KS55PS Originalbetriebsanleitung Seite 24

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
16. Accessories
This manual may contain descriptions of acces-
sories that are not included in the scope of sup-
ply of your machine!
Guide System
2 Pieces guide rails (A) á 700mm
1 Piece rail joiner (F)
1 Piece tilt protection
2 x professional screw clamps (B)
1 x dust bag (21)
1 x non-return mechanism (D)
Guide Device (Fig. 10, 11)
The guide rails (A) enable clean, precise cuts and pro-
tect the surfaces from damage.
When sawing with the guide rail, the cut depth is 4.5
mm less than the scale value on the machine.
For safety, the guide rail can be secured with screw
clamps (B) (not included).
The tilt protection prevents the plunge saw from tilting
during miter cuts and adjustment work.
The rebound protection (D) ensures a safe guiding
during plunging into the workpiece (not included).
By means of the rail joiner (F), 2 guide rails can be
connected and allow long, precise cuts
The guide clearance of the assembly on the guide rail
can be regulated with the two adjustment screws (E).
With the offered accessories, miter cuts, corner cuts
and other fitting tasks can be carried out.
When first using this saw on the optional guide rail,
it will need to be adjusted to slide with minimal side
movement on the guide rail, Adjustable cams (Fig 10
"E") are fitted to do this.
1. Place saw on guide rail.
2. Turn cams (Fig 10 "E") anti-clockwise until tight.
Then clockwise slightly to allow clearance. While
holding dials in position lock in place by screwing
down the Socket head Cap screws in the middle
of each Cam (5mm allen key supplied with ma-
chine)
3. Pull saw back and forth along rail ensuring it
slides smoothly
Re-adjust as needed.
4. Future adjustment may be needed depending on
use of saw.
Splinter Protection (guide rails)
The guide rail comes with a splinter guard, which
must be fitted before the first use.
1. Secure rail with the screw clamps to a piece of
scrap lumber.
2. Adjust the guide clearance on the rail with the two
adjustment screws (E).
3. Set the plunge saw to ca. 6mm cut depth
4. Set up the saw at the back end of the rail.
5. Switch on the machine, press down to the set cut
depth and fit the splinter guard along the whole
length in one pass without stopping.
24
GB
The edge of the splinter guard now corresponds
exactly to the cutting edge of the saw blade
Caution!
Always secure the workpiece in such a way that
it cannot shift.
Always move the machine forward; never pull it
toward the body.
TO SAW:
1. Set the saw on the guide rail.
2. Switch on the machine.
3. Press the saw slowly down to the set cut depth
and move this evenly forward along the rail.
PLUNGE CUTS:
To Saw:
1. Set the saw on the guide rail at the marked cut-
ting point
2. Secure the rebound protection or fence (acces-
sory not included) at the back and front cut points
on the guide rail.
3. Switch on the machine.
4. Press the saw down slowly to the set cut depth
and move this forward evenly on the rail up to the
front cutting point.
Tilt Protection
Put the rail saws with a the supplied anti-tilt. This pre-
vents the machine from tilting sideways when tilting.
This physical injuries or damage to the machine can
be avoided.
Use of the dust bag (Fig. 12)
Push the dust bag (21) onto the extraction nozzle
(12).

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

3401802901

Inhaltsverzeichnis