Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Skipping or repeating tracks
APF = Automatic Program Finder
Prerequisite
are pauses of at least 3 seconds between
music selections (without announcer text or
the like).
Not suited
are music selections with very quiet passages
(e.g., classical music) because such passages
are treated as pauses.
¡
¡
RADIO
CD
¡
AIM TP
AM ON
The AM reception area
(153 ... 279 ... 531 ... 1602) is switched
AM OFF
off by »
«.
Then the Radio button has no function.
Auto LEARN (radio mode)
If you are in a reception area where "RDS
channels with traffic radio reports" cannot
be received well, you can suppress the
"Auto LEARN (LRN) during radio operation".
LRN ON
»
«: Auto LEARN
LRN OFF
»
«: no Auto LEARN when volume
VOL 4
is set higher than »
«.
Automatic changes between regional
broadcasts
If an RDS channel consists of different
re-gional broadcasts, it can occur that your
car radio switches between different
regional broadcasts because of the recepti-
on area.
REG ON
»
« automatic switching between
regional broadcasts is possible.
REG OFF
»
« no switching to a different
regional broadcast.
Downloaded from
www.Manualslib.com
Skipping the currently played track:
Traffic announcements
>
Briefly press the
button. The display
APF +1
indicates "
".
Switching on AIM TP
¡
Hold down
button briefly
AIM TP
Skipping tracks, eg. 4 (max. 9):
TP
»
« appears in the display.
During fast forward wind, repeatedly press the
APF +4
>
button until "
" appears in the
Switching off AIM TP
display.
¡
Hold down
AIM TP
button briefly
TP
»
« disappears from the display.
Repeating the currently played track:
<
Briefly press the
button. The display
Ejecting the cassette
APF -1
indicates "
".
"
Briefly press the
button.
Repeating tracks, eg. 6 (max. 9):
U III
<
During fast rewind, repeatedly press the
APF -6
button until "
" appears in the
Ending cassette play
display.
Radio mode:
¡
CD+
¡
press the
RADIO
button.
¡
CD–
or
briefly press one of the station
1 2 3 4 5
buttons
CD mode:
press the
¡
button.
CD
The cassette remains in the compartment!
"
<
>
1
–
2
U III
The previous sound and geometry settings are
Switching on and off with the ignition
reactivated when the unit is switched back to
switch
radio mode.
IGN ON
»
« You can switch the car radio on
and off with the ignition switch.
CD input sensitivity
IGN OFF
»
« Switching on and off only with
Adjusting the CD player: (Internal CD part)
¢ ¢
the
rotary knob.
CDS MID
»
« middle
CDS HIGH
»
« high
Mute during phone mode
CDS LOW
»
« low
with car telephone
PHONE OFF
»
« no evaluation of the
CD input sensitivity
telephone connection
Adjusting of a CD player: (e.g. MCD 30)
PHONE ON
MCD LOW
»
« The car radio is muted auto-
»
« low
MCD MID
matically when a telephone
»
« middle
MCD HIGH
call is made.
»
« high
PHONE IN
»
« The car radio is switched on
automatically when a tele-
Volume limitation during switching-on
ON VOL - -
phone call is made, and the
»
«: no limitation or
conversation is heard
ON VOL 35
»
«: maximum volume, e.g. 20
through the speakers.
(- - ... 11 ... 35).
The volume is only limited if the volume of
Please read the notes in the chapter
the car radio at switch-off is higher than
»Warning when using automatic aerials«
the set value!
on page 3!
Minimum volume for traffic announce-
When you change the sound and geometry
ments
settings during a telephone conversation,
TA VOL 16
»
« (5 ... 35)
these settings are stored for the next tele-
phone conversation.
For reasons of traffic safety the vol-
ume for announcements should not be set
too high!
manuals search engine
EXPERT
Cassette
Settings
EXPERT
A great number of possible settings
To make car radio operation as easy as possi-
ble, numerous settings that you need only
once or occasionally are located in an additio-
nal control level (EXPERT).
Setting
1. Activating the EXPERT function
"
LOUD
Press the
EXPERT
sounds.
2. Selecting settings
Select from
Possible settings
the setting you wish to check or alter.
Example:
Change display contrast
.
LCD 25
Turn the
¢ ¢
rotary knob until the desired
LCD 25
setting "
EXPERT
Volume
Speed dependent volume
» SCVOL « (0 ... 67)
Setting is only possible if a speed depend-
ent signal is emitted at the
SCV connection (A1).
SCVOL - - -
»
«: SCV switched off
SCVOL 0 67
»
«: Maximum effect
The resulting increase in volume is indicated
by the left digit (or digits).
For experts: Numerical value x 1.25 = volume
increase in db (max. 20 db).
Examples:
SCVOL 16
67
»
*
SCVOL 8
67
»
*
*
These numbers appear only while the vehicle is in mo-
tion and of acorresponding speed.
A change of this number occurs only while
the vehicle is in motion
(condition: Setting EXPERT Menu).
For reasons of traffic safety, the fol-
lowing adjustment should be done by the
passenger!
3. Activating the setting
"
LOUD
Briefly press the
button:
EXPERT
"
E
" appears in the display
RDS – – – TP AF LOUD MONO
CR
LCD88825
DX
E
4. Changing the setting
Set the desired contrast using the
¢ ¢
rotary
knob. The display indicates, for example:
button until the signal
RDS – – – TP AF LOUD MONO
CR
LCD88853
DX
E
...
5. Ending the setting
"
LOUD
Briefly press the
button:
EXPERT
"
E
" disappears from the display.
6. Selecting the next setting
(repeat the steps 2 to 5).
" appears in the display.
7. Deactivating EXPERT
"
LOUD
Press the
button until the signal
EXPERT
sounds.
Adjustment:
1. Vehicle is stopped, engine is running:
Set desired volume with
¢ ¢
rotary knob.
2. Prepare EXPERT setting:
"
LOUD
Hold down
button until signal tone
EXPERT
¢ ¢
sounds. Turn
rotary knob until
SCVOL ...
"
LOUD
»
« in the display. Press
EXPERT
button briefly until »
E
« appears.
3. For higher speed:
Set desired volume with
¢ ¢
rotary knob,
SCVOL 60
e.g. »
« in display.
"
LOUD
Hold down
button until signal tone
EXPERT
sounds.
Acoustics system
« : Maximum set effect.
You can adjust the bass and the treble for the
Maximum volume
front and the rear speakers separately.
increase
You can adjust the settings between –3 and
« : Maximum set effect.
+ 3 with the
¢ ¢
rotary knob.
Medium volume increase
Bass – front speakers
BAS F 0
»
« (F = Front)
Bass – rear speakers
BAS R 0
»
« (R = Rear)
Treble – front speakers
TRE F 0
»
« (F = Front)
Treble – rear speakers
TRE R 0
»
« (R = Rear)
Possible settings
...
......
Display shows: »
«
Activate coding
CODE
If »
« appears in the display the
coding is not activated.
SAFE
If »
« appears in the display the
coding is activated.
Change display contrast
LCD 25
»
« (00 ... 63), adjust according
to installation position of car radio.
Setting can best be adjusted "at dark".
Display colour
Vario-Color (from green to red)
COL 25
»
« (00 ... 53).
Security LED (on/off)
BLK ON
»
« CD button flashes when unit,
LED, and ignition are off.
BLK OFF
»
« CD button does not flash.
Signal tone (on/off)
BEEP ON
»
« A signal tone sounds when
functions are changed.
BEEP OFF
»
« No signal tone sounds when
functions are changed.
EXPERT
Switch-on/off delay for connected booster
(Switching voltage for booster = contact C6)
BDLY ...
»
« (O6 ... 99)
In case of "switching noises": increase or
decrease set value until switching noises
are no longer audible.
AIM function (on/off)
AIM ON
»
« or
AIM OFF
»
« – no AIM memory standby
when car radio is switched off
AIMT standby
AIMT 2:00
»
«
Period of time during which traffic announ-
cements are recorded after the device has
been switched off.
Available settings:
min. 1 minute, max. 4 hours.
AIM TIMER 1 (switch-on time 1),
page 13: AIM function.
Current time is set:
or
!
T 1 OFF
»
« : TIMER 1 is off
T 1 23:59
T 1 OFF
T 1 00:01
»
«
»
«
»
«
Turn
¢ ¢
rotary knob quickly:
quick change of the switch-on time.
Werbung
Inhaltsverzeichnis
