Grundig Advance CC Serviceanleitung Seite 11

Amplifier
Overload protection
At high ambient temperature and volume, the
overload protection circuit may respond.
As long as the overload is not removed, the
rear output stages of the amplifier are swit-
ched off.
¡ ¡ ¡
RADIO L RN/AS P TY/DX
"
A S P
¡
AIM TP
MONO
Manual frequency tuning
1. Select a range: U l, U ll, U lll, AM.
< >
2. Press the or button until the 2nd
signal sounds.
MAN
The display indicates " " and the
frequency tuned to.
3. Tune to the desired frequency.
< >
Press the or button
briefly (frequency steps) or
a longer time (fast frequency scroll).
The display indicates, for example,
MAN 92.70
" ".
4. Terminate manual frequency tuning.
¡ ¡
Press the U III or RADIO or
" button.
AF
Downloaded from www.Manualslib.com
Radio
After selecting the range:
Selecting the RADIO programme source
you will hear the station last tuned to in this
range (Last-station-memory).
In cassette or CD mode:
briefly press the ¡ button.
RADIO
Stereo reception (VHF only)
Range selection
You are receiving a stereo broadcast if the
¡ display indicates " ".
Repeatedly press the button.
RADIO
U ranges U l, U ll, U lll (FM):
Manually switching to mono:
VHF 87.5 ... 108.0 MHz
"
A S P
To switch between the U ranges:
Press the button until the signal
MONO
¡
repeatedly and briefly press the U III
sounds. The ASP function is only effective in
VOICE
button.
the " " position.
" " appears in the display.
AM 153 ... 279 ...531 ... 1602 kHz
Switching back to stereo: press the
button until the signal sounds.
< >
1 – 5 ¡
U III
Calling up stored stations/RDS programmes
1 1 2 2 3 3 4 4 5 5
Station buttons
Press the programme position button briefly.
The contents of the memory position buttons
Select a range: Ul, Ull, Ulll, AM.
are preserved even if the car radio is
Setting the station/RDS programme:
disconnected from the operating voltage.
If the station/RDS programme tuned to is
already stored in the selected range, for exam-
U I
ple, " ", on a programme position button,
the corresponding number is indicated on the
display.
Storing the set station/RDS programme
Press the programme position button until the
signal sounds.
If "AF" is switched off, this setting is also
stored in memory.
¡ ¢ ¢ ¡ "
RADIO L RN/AS AF
¡ 1 5 ¡
AIM TP – U III
manuals search engine
Setting RDS programmes with the
LEARN memory
With the push of a button
you can store up to 24 RDS programmes in
the LEARN memory!
You can call up the stored RDS programmes
manually (RDS-SCAN) or automatically
(AUTOSCAN) one after the other.
Allocating the LEARN memory
Ranges: U I, U II or U III.
¡
Briefly press the L RN/AS button:
RDS programmes (max. 24) being received in
"
A S P the reception area are stored in memory.
MONO
LRN ...
" " appears in the display .
After storing you will hear the RDS program-
me having the best reception quality or only
RDS programmes with traffic announcements
¡
if the AIM TP button has been "activated".
On/off: press the ¡ button.
AIM TP
– manually (RDS–SCAN)
(Repeatedly) briefly press the
RDS SCAN
" " appears in the display.
After that you hear the next RDS programme.
Radio
Alternative frequencies (AF)
AF
The display indicates "
You are receiving an RDS programme that
is being broadcast by several stations with
different frequencies.
Switching off the AF function
When you are in an area with very poor recep-
tion conditions it may happen that short pau-
ses occur while the radio is searching for the
alternative frequencies. It is best in this case
to switch the AF function off.
"
Press the AF button until the signal sounds.
The "AF" function is switched off.
Switching the AF function on
"
Press the AF button until the signal sounds.
Your car radio always selects automatically
the same RDS programme with the alternative
frequency giving the best reception quality.
– automatically (AUTOSCAN)
Press the ¡ button until the signal
RADIO
sounds.
AUTOSCAN
" " appears in the display.
After that all RDS programmes are called up
one after the other for approx. 10 seconds.
If the called up station is to be maintained,
briefly press the ¡ button.
RADIO
RESET
" " appears briefly in the display.
Automatic station store Autostore
The 5 strongest stations of the selected
range received in your reception are are
automatically stored in the station
buttons 1 – 4
Select the desired range: U I, U II, U III, MW
or LW.
Press the ¡ button until the signal
L RN/AS
sounds.
AS
The display indicates " " and the frequency
< >
scrolls on the display.
or button:
After that you hear the programme having the
best reception quality.
Traffic announcement standby (TP)
" TP = TRAFFIC PROGRAM
The radio is in traffic announcement standby
TP
if the display indicates " ".
Switching on and off AIM TP:
¡
Press the button briefly.
AIM TP
If the set station is not a traffic radio station,
a search for the next traffic radio station starts
automatically.
Traffic announcements begin at a minimum
volume:
During the announcement you can adjust the
¢ ¢
volume with the rotary knob.
You will hear only traffic announcements
when the volume at the ¢ ¢ rotary knob is set
to "zero".
Cassette or CD mode stops
during a traffic announcement.
Breaking off the traffic announcement:
¡
Press the AIM TP button briefly.
If the set traffic radio station can no longer
be picked up, a traffic radio station which can
be received better will be automatically set:
LRN ...
» « appears in the display.
Radio
Setting stations/RDS programmes with
the search function
Select the desired range: U I, U II or U III.
< >
Press the or button until the signal
sounds.
The display indicates, for example,
FM 92.70
" ".
The search stops at the next station or RDS
programme.
The search function is set to maximum
sensitivity if
DX
" " appears in the display.
– This occurs automatically after the first scan
of the entire frequency range.
DX
– Switching manually to " ":
¡
press the P TY/DX button until the signal
sounds.
DX
– Switching off " " :
¡
press the P TY/DX button until the signal
sounds.
Only stations/RDS programmes with traffic
announcements are searched if
the ¡ button is "activated".
AIM TP
¡
On/off: press the AIM TP button.
Radio
Memorize traffic announcements (AIM)
AIM = AUTOMATIC INFO MEMO
AIM function
The traffic announcements of the set traffic
radio station are stored automatically:
– while the car radio is on.
– after the car radio has been switched off:
memory standby for a maximum of four
hours.
– if TIMER has been preselected, e.g. every
morning at the same time or before going
on a trip. You can set any two switch-on
times. Maximum memory standby per timer
is four hours.
Set current time
To know at what time a traffic announcement
was stored and to ensure that the TIMER pre-
selection works, you have to set the "Current
time".
EXPERT settings page 21:
Current time manual or
Current time automatic.
AIM function (on/off)
AIM TIMER 1 (switch-on time 1)
AIM TIMER 2 (switch-on time 2)