DeWalt DCF6202 Übersetzung Der Originalanweisung Seite 15

Inserting Collated Screw Strips (Fig. D)
NOTICE: Use only screw strips that are suitable to this
magazine. Only insert screw strips when the screwdriver
power is off and the trigger is locked.
Proper use of collated strips will reduce the risk of injury, reduce
jams and prevents screws from damaging workpiece. For best
performance use new, undamaged strips free of debris.
1. Take a collated strip, holding the plastic portion, and feed
from the bottom of the screw guide
of the advancing mechanism
2. Continue feeding the strip until the first screw is one slot
below the driver bit.
Setting Screw Depth (Fig. A)
Turn fine depth adjustment
from behind the tool) to make the screw head stop raised from
the workpiece.
Turn fine depth adjustment
head stop deeper into the workpiece.
There is a fine depth adjustment indicator
in the adjustment range the tool is. When the slider is furthest
from the tool the screw head will stop in the most raised
position. When the slider is closest to the screwdriver tool the
screw head will stop in its deepest position.
Driving Screws (Fig. A)
1. Before driving screws, ensure screwdriver drive direction is
switched to forward position.
nOTE: Always hold the screwdriver perpendicular
to workpiece.
2. With the magazine installed on the screwdriver, position
shoe 7 on workpiece in location where screw is to
be driven.
3. Switch the screwdriver on by holding the trigger in the on
position. Continue to hold trigger or engage the trigger
lock-on.
4. Apply pressure against workpiece. This will advance screw
into alignment with screwdriver bit.
5. Continue to apply consistent pressure until screw is driven
in completely and screwdriver clutches disengage.
6. Lift screwdriver from workpiece.
The magazine is designed to drive screws completely into
workpiece only. Once screwdriver is lifted, adjustments to screw
must be made by first removing magazine.
Rotating the Collated Attachment
This attachment has the ability to rotate without being taken off
the drywall screwdriver. To rotate, grip the top portion with one
hand, while holding the drywall screwdriver with the other then
rotate. An audible "click" indicates the magazine is in each of the
available positions.
1 and into the bottom
5 .
3 counterclockwise (as viewed
3 clockwise to make the screw
to show where
4
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
For best performance clean magazine by:
1. Remove advancing mechanism from collated magazine
(refer to Removing and Installing the Advancing
Mechanism instructions).
2. Using compressed air and a clean cloth, clean all visible
areas and cavities from dust. Wipe clean as needed on both
the advancing mechanism and collated housing.
3. Reassemble and continue use.
Removing and Installing the Advancing
Mechanism (Fig. E)

CAUTION: The advancing mechanism is spring loaded.
Two hands must be used to remove the advancing
mechanism. The spring may eject from the mechanism.
To Remove advancing Mechanism
1. Remove collated magazine attachment from screwdriver.
2. Slightly depress advancing mechanism
the shoe with one hand.
7
3. Keeping pressure on the shoe
lever 11 so that the pins rotate out of the guide track.
4. Slowly release pressure from the shoe
mechanism is out of the collated housing
EngLIsh
5 by pushing on
7 pull down on the release
until the advancing
7
6 .
13