Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
•
Store the product in such a way as to prevent mechanical failure.
•
When the product is installed, operated or stored in a
non-ventilated area, make sure the room is designed to prevent
the accumulation of refrigerant leaks resulting in a risk of fire or
explosion due to ignition of the refrigerant caused by electric
heaters, stoves, or other sources of ignition.
•
Only persons with a current valid certificate from an
industry-accredited assessment authority, which authorizes their
competence to handle refrigerants safely in accordance with an
industry recognized assessment specification, can work on or
break into a refrigerant circuit.
•
Servicing can only be performed as recommended by the
equipment manufacturer. Maintenance and repair requiring the
assistance of other skilled personnel can only be carried out
under the supervision of the person competent in the use of
flammable refrigerants.
•
When defrosting and cleaning the product, do not use any
means other than those recommended by the manufacturing
company.
•
Do not puncture or heat any part of the refrigerant circuit.
Installing the product
•
Place the product on a flat, level surface.
Only move the product in an upright position.
-
-
Leave a minimum of 0.5 m space around the air inlet and outlet
to allow a good circulation of airflow.
If the product has been tilted, allow it to stand upright for 2 hours
-
before plugging it in.
Assembling the exhaust (image B)
Only use the provided exhaust hose.
-
-
Do not block the exhaust hose, this may cause overheating.
1. Assemble the window kit A
w
2. Install A
in the window opening.
r
3. Tighten A
.
4. Assemble the exhaust hose A
the exhaust hose connector A
q
5. Connect A
the air outlet A
8
6. Extend A
up to 1500 mm.
-
Do not twist the exhaust hose.
-
Ensure that the exhaust hose does not kink.
9
w
7. Snap A
into A
and fasten with the exhaust nozzle screw
t
A
.
Assembling the continuous drainage (optional)
1. Open the continuous drainage outlet A
5
2. Connect A
to a water container or drainage system (not
included).
Using the control panel (image C)
Button
Function
Display
3
C
Switch the product on or off.
7
C
Activate sleep mode. Only works in cooling mode.
w
C
After one hour the set temperature increases 1 °C
and again after 2 hours.
Switch on fan mode.
8
C
Switch to low fan speed.
C
9
Switch to high fan speed.
C
q
Switch on dehumidifying mode.
C
1
2
C
Switch on cooling mode. Use C
the desired temperature.
w
r
the fasteners A
.
8
9
, the exhaust nozzle A
q
.
6
.
5
.
6
e
and C
to set
Indicates that the water reservoir is full.
4
C
5
C
Press timer C
duration of cooling.
Using the remote control (image D)
Button
Function
Switch the product on or off.
7
D
Activate timer mode.
6
D
Activate sleep mode. Only works in cooling mode.
4
D
After one hour the set temperature increases 1 °C
and again after 2 hours.
Switch operating mode.
5
D
Switch fan speed.
D
2
Increase values.
D
1
Decrease values.
3
D
Manual drainage
4
1. C
flashes and the product emits an alarm sound to indicate
that the water reservoir is full.
2. Switch off the product using C
7
3. Unplug A
4. Place a water container underneath A
5. Unscrew the manual drainage cap.
6. Remove the water plug.
7. Slightly tilt the product backwards to ensure all water leaves the
reservoir.
8. Put back the plug and screw the drainage cap back on.
Cleaning the product (image E)
Clean the product regularly as follows:
1. Switch off and unplug the product when not in use or before
and
maintenance.
2. Pull off the grids E
3. Remove the filter screens E
2
4. Clean E
in warm water (about 40 °C) with a neutral detergent.
5. Rinse and dry E
2
6. Put back E
1
7. Put back E
8. Clean the outside of the product with a soft, clean, lightly damp
cloth.
-
Do not use aggressive chemical cleaning agents such as
ammonia, acid, acetone or gasoline when cleaning the product.
5
5
6
and use C
and C
7
.
4
.
1
.
2
1
from E
.
2
in the shade.
1
in E
.
2
together with E
.
e
to set the
Werbung
Inhaltsverzeichnis
