Conrad 97 37 66 Bedienungsanleitung Seite 2

O P E R A T I N G I N S T R U C T I O N S
1+1-Port SATA-III-PCI-
Express- Card
Item-No 97 37 66
Intended Use
The product is intended to be installed in a PCI Express slot on a computer, where it
provides an internal SATA port and an external eSATA port (SATA 6Gb/s = SATA-III).
This product complies with the applicable National and European requirements. All
names of companies and products are the trademarks of the respective owner. All
rights reserved.
Package Contents
• Plug-in card
• Low profile slot bracket (for installing the plug-in card in a flat computer case)
• Data carrier with driver
• Operating Instructions
Features
• Intended for installation in a PCI Express slot
• An internal SATA port and an external eSATA port, each with SATA 6Gb/s
(=SATA-III, compatible with SATA 3Gb/s and SATA 1.5Gb/s)
• Access LED port on each SATA port
Installation
If in doubt about how to install the device correctly, please contact an
EXPERT or a specialist workshop and let them do the installation!
Incorrect installation can damage both the plug-in card and the com-
puter, along with all connected devices.
Caution, Danger!
Switch off the computer in which the plug-in card is to be installed,
and all connected devices, and disconnect all devices from the mains
voltage, remove the plug from the mains! Just turning off at the on/off
switch is not enough!
• Open your computer's housing and carefully remove the cover.
• Locate a free PCI Express slot, remove this slot's cover and insert the card into the
PCI Express slot. Screw the plug-in card firmly into place and make sure it is posi-
tioned correctly in the slot!
For the installation of the plug-in card in a flat computer case, a low-profile
slot bracket is provided. Remove the long slot bracket from the plug-in card
and then install the short low-profile slot bracket.
• Each SATA port has a LED connection. During read/write access to the appropria-
te SATA port, the associated LED flashes. If available, connect a LED connection
on your case cover with the corresponding pin socket on the plug-in card.
Pay attention to the correct polarity when connecting the LED (take note of the „+"
marking on the board), otherwise the LED will not light up.
„P1 LED" = LED connection for SATA port „P1"
„P2 LED" = LED connection for SATA port „P2"
• Connect the internal SATA connection with an appropriate SATA drive. If you do not
have a SATA 6Gb/s drive, you may, of course, connect a „slower" SATA drive.
• Secure all cables, so that they cannot slip out of the ports and so they do not
obstruct a fan in the PC case.
• Close the computer case.
• Connect your computer and monitor to the mains voltage and switch on all devices.
• If your computer does not start correctly, switch it off immediately and check all the
settings and cable connections.
It must be disconnected from the mains power supply before restar-
ting, see above!
Driver Installation
www.conrad.com
After Windows has started, it recognises the plug-in card automatically as new hard-
ware.
Version 03/10
Interrupt the search for the driver. Place the enclosed CD into an appropriate drive on
°
your computer.
At the time when these operating instructions were written, the driver was to be found
in the directory „SATA6G_M9128". Start the programme „drvSetup.exe" in this
directory and follow the instructions.
The computer may have to be restarted after installing the driver, before the SATA
plug-in card will function correctly.
Disposal
© Copyright 2010 by Conrad Electronic SE.
Please dispose of the device when it is no longer of use, according to the cur-
rent statutory requirements.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.