Installing The Blade - Sparky Professional TH 65 Originalbetriebsanleitung

WaRNiNg: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance or in case of mains
drop-out.
sWiTcHinG On - sWiTcHinG Off
brief activation
Switching on: Press ON/OFF switch (1).
Switching off: Release ON/OFF switch (1).
continuous operation
Switching on: Press ON/OFF switch 1 and in
pressed position lock it by button (3).
Switching off: Press ON/OFF switch 1 once and
release it immediately.
In case of mains drop-out during operation while
the lock-on button (3) is engaged, release the
lock-on button immediately.
Do not lock the ON/OFF switch by button (3) while
performing jobs which may require instant stop-
ping of the saw.
Upon switching model TH 70E on, the work area
is locally illuminated.
Max. radiant power: < 2mW
Wavelength: 400-700nm
EN 60825-1: 1994+A1:2002+A2:2001
lED raDiaTiOn
DO nOT sTarE inTO bEam
class 2 lED prODUcT
aDJUsTinG THE spEED (TH 65E, TH 70E)
Adjusting the speed improves the performance
quality and prevents the surface of the processed
material from damage.
The stroke rate can be adjusted by turning the
regulator (2) in the direction, marked by arrows.
(Fig.1)
Hold your saw in normal operation position and
rotate the thumbwheel (2) counter clockwise to in-
crease speed. Turn the thumbwheel (2) clockwise
to reduce speed.
nOTE: Adjusting the speed improves the per-
formance quality and prevents the surface of the
processed material from damage.
If you wish to lock the switch on at a given speed,
depress the switch trigger, push in and hold the
Original instructions
pages-TH 65-65E-70E-R2.indd 7
lock-on button. Adjust the variable speed regula-
tor until the desired speed is reached.
nOTE: If the variable speed regulator is fully turned
in clockwise direction (zero setting for TH 65E or
A setting for TH 70E) your saw may not run.
If you choose not to use the variable speed regula-
tor, turn it entirely in counter clockwise direction.
This will allow the speed of your saw TH 65E to
be controlled by the pressure on the switch trigger
only (for model TH 70E the speed can be adjusted
only by means of the regulator and does not de-
pend on the pressure on the switch trigger).
Avoid operating the saw at low speed for extend-
ed period of time. Otherwise you may cause over-
heating the saw. If this occurs, cool the saw by
running it at no load and full speed.
The stroke rate must suit the kind of processed
material. The following guidelines may be used in
determining correct speed for various applications:
▪ LOW speed is appropriate for starting cuts.
▪ MEDIUM speed is suitable for cutting hard met-
al, plastics and laminates.
▪ HIGH speed produces best results when cut-
ting wood, aluminium, brass and copper.
Define the optimum speed by making a test cut in
a piece of waste material.
blaDE iNsTalliNg (Fig.2)
WaRNiNg: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance or in case of mains
drop-out.
▪ Remove the fence (4).
▪ Press the blade (7) slightly to the roller guide
(10).
▪ Press the blade quick release button (17).
▪ Pull the blade out.

iNsTalliNg ThE blaDE

WaRNiNg: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance or in case of mains
drop-out.
▪ Insert the blade until you hear an audible click,
indicating that the blade shank has entered into
the fixing apertures.
▪ Check to make sure the quick release button
(17) is back in its initial position.
7
EN
20.10.2011 г. 15:31:45