Maintenance - Sparky Professional TH 65 Originalbetriebsanleitung

minium, use a coarser-tooth blade or lower speed.
We recommend applying oil along the cutting line
to keep the blade cool, increase efficiency, and
prolong blade life. Clamp the material firmly and
cut close to the clamping point to eliminate any
vibration of the workpiece being cut.
When cutting conduit, pipe or angle iron, clamp
work in a vice if possible and saw close to the vice.
To cut thin sheet, place the sheet between two
hardboard or plywood supports, and clamp the
layers to o eliminate vibration and material tearing
thus achieving a clean and smooth cut. Lay out
your pattern or line of cut on the top layer.
impOrTanT: When cutting metal, keep the ex-
posed portion of saw bar clean and free of metal
chips by wiping frequently with an cloth soaked in
oil. Use extreme caution in disposing of this cloth
after completion of job to prevent potential fire
hazard.
DUsT EXTracTiOn
The jigsaw is delivered with a dust extraction
adapter (9), fitted to the base plate (TH 70Е) or the
tool body (TH 65, TH 65E). The dust extraction
adapter facilitates air suction around the blade,
thus extracting the dust and chips from the cutting
line to improve operator's scope of vision.
TO insTall:
▪ Unplug the saw.
WaRNiNg: Failure to unplug the saw
may result in accidental starting and possible
serious injury.
▪ Attach the dust extraction adapter to the base
plate rear or to the body. (Fig.8)
▪ Connect the dust extraction adapter to a dust
collection system or a vacuum cleaner.
TO rEmOvE:
● Unplug the saw.
WaRNiNg: Failure to unplug the saw
may result in accidental starting and possible
serious injury.
▪ Draw out and remove the adapter.
paRallEl gUiDE
The jigsaw is delivered with a parallel guide (12),
which is a convenient device for making crosscuts
and rip cuts.
Original instructions
pages-TH 65-65E-70E-R2.indd 9
TO insTall:
▪ Unplug the saw.
WaRNiNg: Failure to unplug the saw
may result in accidental starting and possible
serious injury.
▪ Insert the parallel guide arm through the two
slots in the base plate. (Fig.9)
▪ Adjust the parallel guide to the desired dis-
tance from the edge of material and fix it by the
screws (13).
maGnEsiUm basE plaTE (TH 70E)
The magnesium base plate (5) with a steel inlay
provides the highest possible stability and is in-
tended for machining metal surfaces without the
anti-scratch shoe (11). For machining sensitive
materials, the anti-scratch shoe (11) prevents
damaging the surface. To attach the anti-scratch
shoe (11), hook it onto the base plate (5) at the
front, press it up at the back and latch. (Fig.10)
accEssOriEs
Th 65 – parallel guide, dust extraction adapter,
hex key.
Th 65E – parallel guide, dust extraction adapter,
hex key.
TH 70E – parallel guide, 4 blades, dust extraction
adapter, hex key.
VII - Maintenance
WaRNiNg: Always ensure that the tool
is switched off and unplugged before attempting
to perform inspection or maintenance.
lUbricaTiOn
All bearings have been pre-lubricated at the factory
with a sufficient amount of high grade lubricant for the
life of the unit under normal operating conditions and
no further lubrication is required.
bRUsh REplacEmENT
When the carbon brushes are worn out, the machine
switches itself off. In this case both brushes must be
replaced simultaneously with genuine brushes at
SPARKY service centre for warranty and post-war-
ranty service.
9
EN
20.10.2011 г. 15:31:45