Atag KD8178BD Gebrauchs- Und Montageanleitung Seite 33

u Fit the equaliser trim
Fig. 8 (20) concentrically
onto the appliance: Slide
it into the recess and
engage it in the
keyholes.
u Screw all the mounting
Fig. 9 (34) to
brackets
the pre-drilled holes in
the appliance door
using hexagon screws
Fig. 9 (35) .
For 16 mm-thick unit walls
= 568 mm-wide recess:
Fig. 10 (23) onto
u Clip spacer
the upper hinge and spacer
Fig. 6 (24) onto the lower
hinge.
u Attach the top cover
Fig. 11 (53) and bottom
cover Fig. 11 (50) to the
mounting brackets.
u Fasten the mounting
Fig. 11 (50) at the
brackets
top and bottom with screws
Fig. 11 (51) so that the
brackets can still be moved
a little to the left and right.
u Strip the protective film off the cover trim
Fig. 12 (22) . Apply the cover trim
Fig. 12 (22) to the projection of the cover
Fig. 11 (53) on the handle side, flush with
the front, and adhesively affix it to the side
wall of the appliance.
u If necessary, shorten the cover strip
Fig. 12 (22) at the bottom: The cover strip
Fig. 12 (22) has to end 3 mm above the
upper edge of the lower mounting bracket
Fig. 6 (50) .
Slide in and align the appliance:
u Slide in the appliance until the covers
Fig. 11 against the side wall of the kitchen unit.
u Extend the adjustable foot.
For 16 mm-thick unit walls =
568 mm-wide recess:
u Allow the spacers to abut
against the side wall of the
kitchen unit.
For 19 mm-thick unit walls =
562 mm-wide recess:
u Align the front edges of the
hinges so as to be flush with
the side wall of the kitchen unit.
For kitchen units (16 mm and 19 mm) with door stop
components (knobs, sealing lips etc.):
u Allow for the extra distance (depth of the door stop compo-
nents): Allow hinges and covers
the extra distance.
u Vertically align the appliance by means of the adjustable-
height feet Fig. 6 (25) , using the accompanying open-ended
Fig. 6 (26) .
spanner
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 11 (53) abut
Fig. 13
Fig. 14
Fig. 11 (53) to protrude by
Putting into operation
w The appliance is now correctly positioned in depth. The
distance from the front edge of the side wall of the unit to the
appliance body is 42 mm all the way round. (Allow for door
stop components, such as knobs and sealing lips.)
Note
Incorrect installation will lead to malfunction!
If the distance is not kept, the door may not close. This may
lead to icing, to condensate forming and to malfunction.
u Be sure to keep to the clearance of 42 mm all the way
round. (Allow for door stop components, such as knobs and
sealing lips.)
Tightly screw the appliance into place in the recess:
u At the top and bottom
of both doors with
Spax screws
Fig. 15 (28) passed
through the hinge
plates.
On the handle side at the top:
u Loosen the screws
Fig. 16 (51) a little.
u Tightly screw the top
mounting bracket
Fig. 16 (50) to the unit
wall using Spax screw
Fig. 16 (29) ø4x19.
u Break off the projecting
end of the cover
Fig. 16 (53) .
Fig. 16 (51) .
u Tighten the screws
u Put on the cover Fig. 16 (53) .
On the handle side at the bottom:
u Loosen the screws
Fig. 17 (51) a little.
u Tightly screw the bottom
mounting bracket
Fig. 17 (50) to the unit wall
using Spax screw
Fig. 17 (29) ø4x19.
u Break off the projecting
end of the cover
Fig. 17 (53) . It is no longer
required.
u Tighten the screws
Fig. 17 (51) .
Fig. 17 (54)
u Put the cover
on the bottom mounting
Fig. 17 (50) .
bracket
u Close the appliance door.
4.4.2 Fitting the unit doors
Fig. 18 (30) are required for both doors.
The fitting aids
Therefore fit the unit doors one after the other.
u Check 8 mm-presetting. (Distance between appliance door
and lower edge of crosspiece)
Fig. 15
Fig. 16
Fig. 17
Fig. 18
33