Elektror HRD Serie Betriebs- Und Montageanleitung Seite 20

8 DECLARATION OF INCORPORATION ACCORDING TO APPENDIX II 1 B
DECLARATION OF CONFORMITY IN ACC. WITH EVPG (ENERGY CONSUMPTION
EN
RELEVANT PRODUCTS ACT).SECTION 4 PARAGRAPH 1
The manufacturer,
Elektror airsystems gmbh
Hellmuth-Hirth-Strasse 2
D-73760 Ostfi ldern
hereby declares that the product to which this declaration refers meets the basic requirements of the Machinery Directive (2006/42/
EC) as set forth below.
Description of incomplete machine:
High Pressure Blower HRD 1/2T, HRD 1/3T, HRD 1/4T, HRD 1/5T, HRD 14/5T, HRD 2/3T, HRD 2/4T, HRD 2/5T, HRD 60/4, HRD
60/5, HRD 60/7, HRD 65/2, HRD 65/4, HRD 65/5, HRD 65/7, HRD 7/12, HRD 7/17, HRD 7/23, HRD 1T FU/FUK,
HRD 14T FU/FUK, HRD 16T FU/FUK, HRD 2T FU/FUK, HRD 60 FU/FUK, HRD 65 FU/FUK, HRD 7 FU, HRD 1T, HRD 14T,
HRD 2T, HRD 60, HRD 65, HRD 7
Serial number and year of manufacture can be found on the nameplate and on the accompanying delivery slip.
Description of the essential requirements of Machinery Directive (2006/42/EC), with which the partially completed
machine complies:
Machinery Directive (2006/42/EC): Annex I, Articles 1.1.2, 1.1.3, 1.1.5, 1.3.2, 1.3.3, 1.3.4, 1.3.7, 1.5.1, 1.6.1, 1.7.1, 1.7.3
Electromagnetic Compatibility Directive (2014/30/EU)
Eco-design Directive for Energy-related Products (2009/125/EC)
Implementation regulation (640-2009): Defi nition of requirements for the environmentally design of electric motors.
The partially completed machine described here continues to fulfi l the protective regulations of the Low Voltage Directive
(2014/35/EC) according to Annex I, No. 1.5.1 of the Machinery Directive.
The commissioning of the partially completed machine is not permitted until it has been verifi ed that the machine in which the
partially completed machine is to be installed, complies with the provisions of the Machinery Directive (2006/42/EC).
The following harmonised standards were applied:
DIN EN ISO 12100 2011
DIN EN 60034-1
DIN EN 60034-5
DIN EN 60034-30-1 2014
DIN EN 60204-1
DIN EN 60664-1
The manufacturer, Elektror airsystems gmbh, undertakes to make the special documentation on this incomplete machine available,
electronically or in hardcopy, to national authorities on demand. The special technical documentation belonging to this incomplete
machine was prepared in accordance with Annex VII Part B.
Mr Steff en Gagg, tel. +49 711 31973-2124, is responsible for the documentation.
Kreher (Managing Director)
Ostfi ldern, 21.07.2020
20
Safety of machinery - General principles of design -
Risk assessment and risk reduction
2011 Rotating electrical machines,
Part 1: Rating and performance
2007 Rotating electrical machines,
Part 5: Degrees of protection provided by the integral
design of rotating electrical machines (IP code) – Classifi cation
Rotating electrical machines,
Part 30: Effi ciency classes of three-phase motors with squirrel-cage rotor,
except pole-changeable motors. (IE-Code)
2019 Safety of machinery – Electrical equipment of machines,
Part 1: General requirements
2008 Insulation coordination for equipment within low-voltage systems,
Part 1: Principles, requirements and tests
Operating and assembly instructions HRD
www.elektror.com