Herunterladen Diese Seite drucken

Werbung

MPA-1
Bestell-Nr. • Order No. 32.0550
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
Mikrofonvorverstärker-Modul
Diese Anleitung richtet sich an Anwender mit
Grundkenntnissen in der Elektronik� Bitte lesen Sie
die Anleitung vor dem Betrieb gründlich durch und
heben Sie sie für ein späteres Nachlesen auf�
1 Verwendungsmöglichkeiten
Über das Modul MPA-1 lässt sich ein Mikrofon an
einen Line-Eingang eines Audiogerätes anschlie-
ßen. Der Mikrofonvorverstärker kann mit einer ent-
sprechenden Spannungsversorgung als Einzelgerät
aufgebaut oder als Modul in ein Audiogerät (z. B.
Verstärker, Mischpult etc.) eingesetzt werden. Zum
Betrieb wird eine Gleichspannung von 12 – 40 V be-
nötigt. Die Stromaufnahme beträgt 6 mA.
2 Wichtige Hinweise für den Gebrauch
Das Modul entspricht allen relevanten Richtlinien der
EU und trägt deshalb das
-Zeichen.
Das Modul ist nach der EMV-Richtlinie 2014 / 30/ EU
aufgebaut (EMV = Elektromagnetische Verträglich-
keit). Damit das Modul auch im Betrieb diese Richt-
linie erfüllt, muss es in ein abgeschirmtes Gehäuse
eingesetzt werden und der Eingang sowie der Aus-
gang müssen über abgeschirmte Leitungen ange-
schlossen werden. Wird die EMV-Richtlinie nicht
eingehalten, erlischt die Konformitätserklärung.
Verwenden Sie das Modul nur im Innenbereich.
Schützen Sie ihn vor Tropf- und Spritzwasser, hoher
Luftfeuchtigkeit und Hitze (zulässiger Einsatztem-
peraturbereich 0 – 40 °C).
Wird das Modul zweckentfremdet, nicht richtig
angeschlossen, überlastet oder nicht fachgerecht
Microphone Preamplifier Module
These instructions are intended for users with basic
electronic knowledge� Please read the instructions
carefully prior to operation and keep them for later
reference�
1 Applications
Via the module MPA-1, a microphone can be con-
nect ed to the Line input of an audio unit. With a
corresponding voltage supply, the microphone pre-
amplifier can be operated as an individual unit or
placed as a module into an audio unit (e. g. amplifier,
mixer, etc.). For operation, a DC voltage of 12 – 40 V
is required. The current consumption is 6 mA.
2 Important Notes
The module corresponds to all relevant directives of
the EU and is therefore marked with
The module has been designed in accordance
with the EMC Directive 2014 / 30 / EU (EMC = elec-
tromagnetic compatibility). To ensure compliance
with this directive also during operation, place the
module in a shielded housing and connect its input
and its output via shielded cables. If the module
does not comply with the EMC directive, the
declaration of conformity will be invalid.
The module is only suitable for indoor use. Protect
it against dripping water and splash water, high air
humidity and heat (admissible ambient tempera-
ture range 0 – 40 °C).
No guarantee claims for the module and no liabil-
ity for any resulting personal damage or material
damage will be accepted if the module is used
ELECTRONICS FOR SPECIALISTS
repariert, kann keine Haftung für daraus resultie-
rende Sach- oder Personenschäden und keine Ga-
rantie für das Modul übernommen werden.
Soll das Modul endgültig aus dem Betrieb
genommen werden, übergeben Sie es zur
umweltgerechten Entsorgung einem ört-
lichen Recyclingbetrieb.
3 Anschluss
Der komplette Anschluss ist in der Abb. 1 dargestellt:
INPUT
Signaleingang, Anschluss für das Mikrofon
Masse für das Mikrofon
OUTPUT
Ausgang
Masse für den Ausgang
+U
Betriebsspannung 12 – 40 V (⎓)
Masse für die Betriebsspannung
4 Inbetriebnahme
Nach dem Anlegen der Versorgungsspannung ist der
Mikrofonvorverstärker betriebsbereit. Mit dem ein-
gebauten Regler die Mikrofonlautstärke einstellen.
Dabei darf das nachfolgende Gerät nicht über steuert
werden.
5 Technische Daten
Frequenzbereich: � � � � � � � � � �20 – 15 000 Hz, −0,5 dB
Eingangsempfindlichkeit: � � � �2 mV bei 0 dB am Ausgang
Eingangsimpedanz: � � � � � � � �200 Ω – 10 kΩ
Ausgangsspannung:� � � � � � � �7 V max� / 1 kΩ
Verstärkung: � � � � � � � � � � � � �52 dB
for other purposes than originally intended, if it is
not correctly connected, if it is overloaded or not
repaired in an expert way.
If the module is to be put out of operation
de finitively, take it to a local recycling plant
for a disposal which is not harmful to the
environment.
3 Connection
The complete connection is shown in fig. 1:
INPUT
signal input, connection for the microphone
ground for the microphone
OUTPUT
output
ground for the output
+U
operating voltage 12 – 40 V (⎓)
ground for the operating voltage
.
4 Setting the Module into Operation
After connecting the supply voltage, the microphone
preamplifier is ready for operation. Adjust the micro-
phone volume with the built-in control. Make sure
not to overload the subsequent unit.
5 Specifications
Frequency range: � � � � � � � � � �20 – 15 000 Hz, −0�5 dB
Input sensitivity: � � � � � � � � � �2 mV with 0 dB
Input impedance: � � � � � � � � � �200 Ω – 10 kΩ
Output voltage: � � � � � � � � � � �7 V max� / 1 kΩ
Gain: � � � � � � � � � � � � � � � � � � �52 dB
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
by MONACOR INTERNATIONAL. All rights reserved.
©
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
15 – 20 000 Hz, −3,0 dB
15 – 20 000 Hz, −3�0 dB
at the output
ELECTRONICS
Störabstand: � � � � � � � � � � � � �> 65 dB
Klirrfaktor: � � � � � � � � � � � � � � �< 0,05 %
Rauschspannung: � � � � � � � � �0,5 µV
Stromversorgung: � � � � � � � � �12 – 40 V (⎓) / 6 mA
Zulässige Einsatztemperatur: �0 – 40 °C
Abmessungen
ohne Achse (B × H × T): � � � � �40 × 25 × 60 mm
Gewicht: � � � � � � � � � � � � � � � �30 g
Änderungen vorbehalten.
Mic
Line
Input
Output
8
5
IC 1
1
4
VR 1
MONACOR MPA-1
C 2
+U 12 – 40 V
9 V
R 12
TR 2
27 k4
TIP 122
C 5
100 µ
D 2
C 6
BZX55C15
10 µ
C7
C7
R 2
D 1
R 5
R 7
BZX55C10
330n
330n
56 k2
10 k
681
TR 1
BC 549
C 1
R 3
22 µ
100
INPUT
R 10
47 k5
C 2
100 µ
R 1
R 4
C 3
R 6
R 8
100 k
221 k
470 p
150
22 k1
VR 1
10 k
S / N ratio: � � � � � � � � � � � � � � �> 65 dB
THD: � � � � � � � � � � � � � � � � � � �< 0�05 %
Noise voltage: � � � � � � � � � � � �0�5 µV
Power supply: � � � � � � � � � � � �12 – 40 V (⎓) / 6 mA
Admissible
operating temperature: � � � � �0 – 40 °C
Dimensions
w/o axle (W × H × D): � � � � � �40 × 25 × 60 mm
Weight: � � � � � � � � � � � � � � � � �30 g
Subject to technical modification.
A-0989.99.04.03.2017
12 – 40 V
TR 2
+U
R 9
1k
IC 1
TL 071
C 4
8
2
7
22 µ
OUTPUT
6
3
5
4
R 11
1
4 k75

Werbung

loading

Inhaltszusammenfassung für Monacor MPA-1

  • Seite 1 Gain: � � � � � � � � � � � � � � � � � � �52 dB damage will be accepted if the module is used Subject to technical modification. MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany A-0989.99.04.03.2017 Copyright by MONACOR INTERNATIONAL.
  • Seite 2 Tensione d’uscita: � � � � � � � � �7 V max� / 1 kΩ gliato, di sovraccarico o di riparazione non a Con riserva di modifiche tecniche. MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany A-0989.99.04.03.2017 Copyright by MONACOR INTERNATIONAL.