Kinderkraft PRIME LITE Bedienungsanleitung Seite 25

III Pram body elements (FIG. 3)
21. Pram body carrying handle
22. Pram body hood
23. Pram body hood folding/unfolding buton
24. Lever for releasing the Pram body from the
frame
25. Pram body and buggy frame connector
IV UNFOLDING BUGGY FRAME In order to unfold the frame, release the locking element (FIG. 4). Holding the handle, lift
the frame (FIG. 5) until you hear a locking sound (FIG. 6)
V WHEEL ASSEMBLY/DISASSEMBLY Insert the front wheels in the slots on the front of the frame until you hear the locking
sound (FIG. 7A). In order to remove the wheels, press the front wheel release button as shown in Figure 8. The buggy has a
system of swivel front wheels with a possibility of locking for straight movement. To lock the wheel for straight movement,
press the upper part of the lock (FIG. 9, movement A). In order to unlock, move the lock up (FIG. 9, movement B). Insert the
rear wheels into the slots in the rear part of the frame until they lock, making sure that the flat surfaces of the axis of the
slot have been set correctly (FIG. 10). To remove the rear wheel, press the release button (FIG. 11).
NOTE! Before using the buggy make sure that all the wheels are
properly installed.
VI USE OF BRAKE The buggy is equipped with a foot parking brake. Press the brake with your foot (FIG. 12.1). The brake is
activated after you hear the sound of the lock. The brake is unlocked after moving the brake lock up (FIG. 12.2).
VII ASSEMBLY/DISASSEMBLY
VII.I SEAT When installing the seat on the buggy frame, stick the seat connector (A) in to the frame slot (B) (one on each
side of the buggy) until you hear a click (FIG. 13.1). The seat may be mounted forward or rearward (FIG. 13.2). When
removing the seat, press the lever for releasing the seat from the frame on the both sides (FIG. 14.1) and pull it up (FIG.
14.2). Baby stroller is equipped with a footrest cover that can be mounted on both the seat and the carrycot. Leg cover
should be mounted using the press studs on the outside of the canopy hinges.
NOTE! Do not fold the buggy frame when the Pram body or the
seat in its rear position is installed on it.
VII.II CANOPY
NOTE! INSTALL THE CANOPY BEFORE USING THE BUGGY
Place the canopy in the guide in the buggy frame and make sure it is properly installed (FIG. 15.1). When removing the
canopy, press the button on either side of the seat and remove the canopy (FIG. 15.2). When installing and removing the
canopy remember about Velcro fasteners on the sides and the zip on the back of the backrest.
VII.III SAFETY BAR When installing the safety bar, insert it in the appropriate guides in the seat frame until it clicks (FIG.
16.1). To remove the part, press the bar release buttons on either side of the guide and remove the safety bar (FIG. 16.2).
VIII SAFETY BELTS Press the button to open the clasp (FIG. 17.1). To secure the child, connect the latches of the hip and
shoulder straps and then insert them into the middle clasp (FIG. 17.2) until it engages.
IX SEAT POSITIONS The seat has 4 positions: lying, 2 x reclining and sitting, adjusted with backrest adjustment lever (FIG.
18.1 and 18.2).
X PARENT HANDLE ADJUSTMENT To adjust the bar, press the handle adjustment buttons on both sides and set it in the
desired position (FIG. 19).
XI FOOTREST ADJUSTMENT The position is changed by lifting the footrest (FIG. 20.1). In order to lower the footrest, press
the footrest adjustment buttons on both sides (FIG. 20.2).
XII FOLDING THE BUGGY (FIG. 21) Make sure that the seat is positioned facing the direction of travel before folding the
buggy. Fold the canopy. Simultaneously press the release button and pull both folding levers to yourself to fold the buggy.
When the buggy is completely folded, the locking element will lock itself. In order to minimize the folded buggy dimensions,
lower the footrest. In addition, set the backrest in the top position to facilitate frame folding.
XIII BUGGY PRAM BODY After removing the Pram body from the packaging, set the hood (FIG. 22A). The hood can be folded
using the Pram body hood folding and unfolding buttons on both sides of the Pram body (FIG. 22B). Place the foot cover
and attach it to the Pram body hood using the press studs (FIG. 23). The foot cover is equipped with an additional panel
protecting from the wind. When the wind blows, it can be attached using a clamp (FIG. 24A). After folding, it must be fixed
using clamp B (FIG. 24B). To adjust the Pram body backrest, move the backrest adjustment lever (RYS. 25) located under the
Pram body and lock in the correct position. The Pram body backrest has 4 levels of adjustment.
XIV ATTACHING THE PRAM BODY TO THE BUGGY FRAME
NOTE! THE PRAM BODY CAN ONLY BE MOUNTED FACING
BACKWARDS (the child faces the person pushing the buggy).
26. Backrest adjustment lever
27. Mattress
28. Rain cover
29. Mosquito net
25