Technical Data; Before Starting The Equipment - EINHELL BT-BD 911 Originalbetriebsanleitung

Anleitung_BT_BD_911_SPK7__ 28.11.14 08:30 Seite 12
GB

5. Technical data

Nominal input voltage
Power rating
Operating mode
Motor speed
Output speed
Speed levels
Drill chuck mount
Scroll chuck
Max. shaft diameter
Reach
Drill depth
Pillar diameter
Height
Weight
L sound pressure level
pA
L sound power level
WA
K uncertainty
pA
K uncertainty
WA
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Load factor:
A load factor of S2 15 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (500 W) for no longer than
the time stipulated on the specifications label (15
minutes ON period).
If you fail to observe this time limit the motor will
overheat. During the OFF period the motor will cool
again to its starting temperature.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Wear protective gloves.
n
12
Caution!
Residual risks
Even if you use this electric power tool in
230V ~ 50 Hz
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
500 W
may arise in connection with the equipment's
S2 15 min.
construction and layout:
1,400 rpm
1. Damage to hearing if no suitable ear protection is
used.
280 – 2,350 rpm
9
B 16

6. Before starting the equipment

Ø 1,5 - 16 mm
Before you connect the equipment to the mains
16 mm
supply make sure that the data on the rating plate
115 mm
are identical to the mains data.
50 mm
Caution!
46 mm
Always pull the power plug before making
650 mm
adjustments to the equipment.
21.5 kg
6.1. Assembling the machine
61.5 dB(A)
Position the machine base (1).
n
74.5 dB(A)
Fasten mounting flange with pillar (2) using three
n
screws (3) and washers to drill base (1).
3 dB
Push the drill table (4) with drill table clamp shaft
n
3 dB
onto the pillar (2) (Fig. 3). Lock the drill table into
the desired position using the clamping screw (5).
Place drill head (6) with V-belt cover (7) and
n
motor (8) onto the drill pillar and fasten using the
Allen screws (20).
Screw the three ball-shaped handles (9) onto the
n
feeder cross handle.
Note: All bare parts are greased in order to protect
them from corrosion. Before mounting the drill chuck
(10) onto the spindle (11), both parts must be
completely degreased using an environmentally
friendly solvent. This ensures optimal transmission of
power.
6.2. Installing the machine (Fig. 1)
Before you use the drill for the first time it must be
permanently fixed in position. Use both mounting
holes (12) in the base plate to do this. Ensure that the
equipment is freely accessible for operation,
adjustment and maintenance.
Note: The fixing screws may only be tightened to a
point where they do not distort or deform the base
plate. Excessive tension can lead to fracture.
6.3. Hinged chip guard (Fig. 4-6)
Unscrew the three screws (21). Push the transparent
cover (23) into the groove of the red mounting frame
(24) and fasten it again with the screws (21).
Then use the clamping screw to fasten the folding