Makita DSC250 Betriebsanleitung Seite 8

5. Do not short the battery. A battery short can
cause a large current flow, overheating, pos-
sible burns and even a breakdown.
· Do not touch the terminals with any conductive
materials.
· Avoid storing battery in a container with other
metal objects such as nails, coins, etc.
· Do not expose battery to water or rain.
· Do not cut the cord.
6.
Do not operate the tool or charge the battery in
explosive atmospheres, such as in the presence
of lacquer, paint, benzin, thinner, gasoline, gasses
or adhesive. This may cause an explosion or fire.
7. Do not charge the battery on paper, cardboard,
cloth, cushions, mats, carpets, vinyl or in the pres-
ence of dust. This may cause fire.
8. Do not expose the Charger to water or metal items
that can short out the charging terminals.
9.
Do not use charger for any other purpose than
charging the battery.
10. Make sure tipped saw blades have no chips or
cracks before using the tool.
11. Do not use water or cutting oil when cutting.
12. Use only Makita genuine tipped saw.
13. Do not leave the tool on the floor with switch
locked on. The tool will run continuously and it
may cause personal injury.
14. Do not operate the tool close to flammable and
fragile items or personnel not necessary to the
operation. During cutting hot debris and sparks will
be ejected from the tool which may cause damage
to the surroundings, fire or personal injury.
15. Do not cut concrete. It causes damage to the tool
and may result in personal injury.
16. Check for the presence of people on the ground
during operation in an elevated place. Any materi-
als or tools dropped may cause an accident.
17. If during charging, there is an abnormal generation
of heat, stop charging immediately by disconnect-
ing the battery. Continuing charging may cause
smoke, fire or explosion.
18. Do not allow anything to cover or clog the motor
vents.
This may cause the motor to overheat.
19. When using an extension cord with the charger,
it is recommended to use a cord with the cross
section below and with a length as short as pos-
sible. For charging outdoors, use a cord rated for
outdoor use.
Relation between usable cord thickness and maximum
length
Cord size
(Nominal cross sectional area of
conductor)
0.75 mm
2
1.25 mm
2
WARNING FOR USING
TIPPED SAW
Work area safety
1.
2.
3.
4.
Dress and protective equipment
5.
6.
Before use
7.
8.
Tipped saw replacement
9.
10. Ensure there is no one in the surroundings before
During operation
11.
Maximum cord
length
12. Hold the material firmly, in a vice or similar, so
20 m
30 m
13. Start cutting only after the Tipped Saw has
8 ENGLISH
Ensure the Dust Bag is fixed correctly. Without the
Dust Bag, when Tipped Saw Blades are damaged,
pieces of the blades fly off and can cause serious
personal injury.
Keep bystanders away from operations. Even with
the Dust Bag fitted, damaged blades or hot debris
can fly out of the bag, resulting in serious personal
injury.
Sparking may occur when cutting with Tipped Saw
Blades. Do not use the tool where there is the risk
of fire or explosion.
Cutting with Tipped Saw Blades is noisy. Consider
the work area environment.
Wear protective equipment; safety glasses, safety
shoes, dust mask and helmet. Even with the Dust
Bag fitted, damaged blades or hot debris can fly
out of the cover, resulting in personal injury.
Dress properly. Do not wear a tie, loose clothing or
knit gloves. Keep hair covered with a hair cover or
a cap to be away from rotating blades.
Ensure that Tipped Saw Blades are not deformed,
chipped, cracked or worn-out. Do not use a Tipped
Saw if any damage or wear is found. Cutting under
such conditions may cause further damage to the
blades and serious personal injury.
Do not use the Tipped Saw for any application
other than that stated in the tool specification.
Using the Tipped Saw for other applications can
cause excessive wear, detachment of blades, low
cutting performance and abnormal generation of
heat, resulting in damage to the blades and seri-
ous personal injury.
When replacing the Tipped Saw, ensure that the
battery is removed from the tool to prevent acci-
dental operation and personal injury.
operation and no abnormal sounds or abnormal
vibrations occur when operating. Operating with
abnormal sounds or abnormal vibrations can dam-
age the blades resulting in serious personal injury.
Do not use the Tipped Saw for any purpose other
than cutting. Do not subject the blades to damage
or stress. It can break the blades resulting in seri-
ous personal injury.
that it cannot move when cutting. If the material
moves, the operation becomes unstable and
cannot be controlled, resulting in damage to the
blades and possible serious personal injury.
reached maximum speed. If the Tipped Saw is set
against the material before the motor is started,
the blades will be overloaded and damaged,
resulting in possible serious personal injury.