Maintenance - Makita RP0900 Betriebsanleitung

To install the straight guide, insert the guide bars into the
holes in the tool base. Adjust the distance between the bit
and the straight guide. At the desired distance, tighten the
wing bolts to secure the straight guide in place. (Fig. 11)
When cutting, move the tool with the straight guide flush
with the side of the workpiece.
If the distance (A) between the side of the workpiece and
the cutting position is too wide for the straight guide, or if
the side of the workpiece is not straight, the straight guide
cannot be used. In this case, firmly clamp a straight board
to the workpiece and use it as a guide against the router
base. Feed the tool in the direction of the arrow. (Fig. 12)
Templet guide (Accessory) (Fig. 13)
The templet guide provides a sleeve through which the bit
passes, allowing use of the tool with templet patterns.
To install the templet guide, loosen the screws on the tool
base, insert the templet guide and then tighten the
screws. (Fig. 14)
Secure the templet to the workpiece. Place the tool on the
templet and move the tool with the templet guide sliding
along the side of the templet. (Fig. 15)
NOTE:
• The workpiece will be cut a slightly different size from
the templet. Allow for the distance (X) between the bit
and the outside of the templet guide. The distance (X)
can be calculated by using the following equation:
Distance (X) = (outside diameter of the templet guide -
bit diameter) / 2
Dust nozzle set (Accessory) (Fig. 16 & 17)
Use the dust nozzle for dust extraction. Install the dust
nozzle on the tool base using the thumb screw so that
protrusion on the dust nozzle fit to the notch in the tool
base.
Then connect a vacuum cleaner to the dust nozzle.
(Fig. 18)

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Straight & groove forming bits
• Edge forming bits
• Laminate trimming bits
• Straight guide
• Templet guide 25
8
• Templet guides
• Templet guide adapter
• Lock nut
• Collet cone 3/8", 1/4"
• Collet cone 6 mm, 8 mm
• Wrench 13
• Wrench 22
• Dust nozzle set
Router bits
Straight bit (Fig. 19)
D A
6
20
1/4"
8 8
6
8
1/4"
6
6
1/4"
"U" Grooving bit (Fig. 20)
D A
6 6
"V" Grooving bit (Fig. 21)
D A
6 20
Drill point flush trimming bit (Fig. 22)
D A
8 8
6 6
Drill point double flush trimming bit (Fig. 23)
D A L 1
8 8 80
6 6 70
Corner rounding bit (Fig. 24)
D A 1 A 2
6 25 9
6 20 8
L 1 L 2
50 15
60 25
50 18
50 18
L 1 L 2
50 18
L 1 L 2
50 15 90°
L 1 L 2 L 3
60 20 35
60 18 28
L 2 L 3
55 20
40 12
L 1 L 2 L 3
48 13 5
45 10 4
mm
mm
R
3
mm
θ
mm
mm
L 4
25
14
mm
R
8
4