Maintenance - Makita MLT100 Betriebsanleitung

Work helpers
Push sticks, push blocks or auxiliary fence are types of
"work helpers". Use them to make safe, sure cuts without
the need for the operator to contact the blade with any
part of the body.
Push block (Fig. 31)
Use a 19 mm piece of plywood.
Handle should be in center of plywood piece. Fasten with
glue and wood screws as shown. Small piece 9.5 mm x
8 mm x 50 mm of wood must always be glued to plywood
to keep the blade from dulling if the operator cuts into
push block by mistake. (Never use nails in push block.)
Auxiliary fence (Fig. 32)
Make auxiliary fence from 9.5 mm and 19 mm plywood
pieces.
Ripping
CAUTION:
• When ripping, remove the miter gauge from the table.
• When cutting long or large workpieces, always provide
adequate support behind the table. DO NOT allow a
long board to move or shift on the table. This will cause
the blade to bind and increase the possibility of
kickback and personal injury. The support should be at
the same height as the table.
1. Adjust the depth of cut a bit higher than the thickness
of the workpiece. (Fig. 33)
2. Position the rip fence to the desired width of rip and
lock in place by pivoting the grip.
3. Turn the tool on and gently feed the workpiece into the
blade along with the rip fence.
(1) When the width of rip is 150 mm and wider,
carefully use your right hand to feed the
workpiece. Use your left hand to hold the
workpiece in position against the rip fence.
(Fig. 34)
(2) When the width of rip is 65 mm - 150 mm wide,
use the push stick to feed the workpiece.
(Fig. 35)
(3) When the width of rip is narrower than 65 mm,
the push stick cannot be used because the push
stick will strike the blade guard. Use the auxiliary
fence and push block. Attach the auxiliary fence
to the rip fence with two "C" clamps. (Fig. 36)
Feed the workpiece by hand until the end is about
25 mm from the front edge of the table. Continue to
feed using the push block on the top of the auxiliary
fence until the cut is complete. (Fig. 37)
Cross cutting
CAUTION:
• When making a crosscut, remove the rip fence from the
table.
• When cutting long or large workpieces, always provide
adequate support to the sides of the table. The support
should be at the same height as the table.
• Always keep hands away from path of blade.
Miter gauge (Fig. 38)
Use the miter gauge for the 4 types of cutting shown in the
figure.
12
CAUTION:
• Secure the knob on the miter gauge carefully.
• Avoid creep of workpiece and gauge by firm
workholding arrangement, especially when cutting at
an angle.
• NEVER hold or grasp the intended "cut-off" portion of
the workpiece.
• Always adjust the distance between the end of the
miter gauge and the saw blade not to exceed 15 mm.
Use of miter gauge (Fig. 39)
Slide the miter gauge into the thick grooves in the table.
Loosen the knob on the gauge and align to desired angle
(0° to 60°). Bring stock flush up against fence and slide
table, secure it with the clamp on the miter gauge and
feed gently forward into the blade.
Auxiliary wood facing (miter gauge)
(Fig. 40)
To prevent a long board from wobbling, fit the miter gauge
with an auxiliary fence board. Fasten with bolts/nuts after
drilling holes, but fasteners must not protrude from the
face board.
Carrying tool (Fig. 41)
Make sure that the tool is unplugged.
Carry the tool by holding the tool part shown in the figure.
CAUTION:
• Always secure all moving portions before carrying the
tool.
• Always make sure that the blade guard is installed in
place before the carrying the tool.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
Cleaning
Clean out sawdust and chips from time to time. Carefully
clean the blade guard and moving parts inside the table
saw.
Lubrication
To keep the table saw in tip-top running condition, and to
assure maximum service life, oil or grease the moving
parts and rotating parts from time to time.
Lubrication places:
• Threaded shaft to elevate the blade
• Hinge to rotate the frame
• Elevation guide shafts on motor
• Gear to elevate the blade
Replacing carbon brushes (Fig. 42)
Remove and check the carbon brushes regularly.
Replace when they wear down to 3 mm in length. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. To
replace the carbon brushes, remove the blade guard and
blade and then loosen the lock lever, tilt the saw head and