Maintenance And Servicing - Bosch GCM 18V-305 GDC Professional Originalbetriebsanleitung

The leg of the angle gauge must be flush with the saw blade
(43) along its entire length.
Setting (see figure X2)
– Loosen all four set screws (73) using the hex key (4 mm)
(17) and turn the saw table (41) together with the scale
(40) until the leg of the angle gauge is flush with the saw
blade along its entire length.
– Re-tighten the screws again.
If the angle indicator (63) is not aligned with the 0° mark on
the scale (40) following adjustment, loosen the screw (74)
using a cross-headed screwdriver and align the angle indic-
ator along the 0° mark.
Adjusting the Clamping Force of the Clamping Handle
(14) (see figure Y)
The clamping force of the clamping handle (14) can be ad-
justed.
Checking
– The clamping force of the clamping handle must hold the
glide arm securely in place at any bevel angle.
Setting
– Loosen the clamping handle (14).
– Use a socket spanner (17 mm) to turn the set screw (75)
anticlockwise to reduce the clamping force or clockwise
to increase the clamping force.
– Set a bevel angle, retighten the clamping handle (14) and
check whether the required clamping force has been
reached.
Transport (see figure Z)
Before transporting the power tool, the following steps must
be carried out:
– Slide the glide arm (33) all the way back and secure it in
this position.
– Make sure that the depth stop (27) is pressed all the way
in and that the adjusting screw (26) fits through the re-
cess without touching the depth stop when moving the
glide arm.
– Guide the glide arm downwards until you can press the
transport safety lock (34) all the way in
– Slide the saw table extensions (8) all the way in.
– Set the bevel angle to 0° and tighten the clamping
handle (14).
– Turn the saw table (41) as far as possible to the left and
tighten the locking knob (12).
– Remove all accessories that cannot be securely fitted to
the power tool.
– If possible, transport unused saw blades in an enclosed
container.
– For transport, hold the power tool by the recessed
handles (16) on either side of the saw table.
When transporting the power tool, only use the trans-
u
port fixtures. Never carry the power tool by the pro-
tective devices, the glide arm or the handle.
Bosch Power Tools

Maintenance and servicing

Maintenance and cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times.
– Remove dust and chippings after each operation with a
paintbrush.
Clean the guide roller (20) regularly.
Accessories
Dust bag
GTA 2500 W saw stand
GTA 2500 Compact saw stand
GTA 2600 saw stand
GTA 3800 saw stand
3 601 M43 000: Saw blades for wood and fibreboard,
panels and strips
Standard for Wood
305 x 2.2/1.6 x 30 mm, 40 teeth
Standard for Wood
305 x 2.2/1.6 x 30 mm, 60 teeth
Standard for Wood
305 x 2.2/1.6 x 30 mm, 96 teeth
Expert for Wood
305 x 2.2/1.6 x 30 mm, 42 teeth
Expert for Wood
305 x 2.2/1.6 x 30 mm, 60 teeth
Expert for Wood
305 x 2.2/1.6 x 30 mm, 96 teeth
3 601 M43 000: Saw blades for aluminium
Standard for Aluminium
305 x 2.4/1.8 x 30 mm, 96 teeth
Expert for Aluminium
305 x 2.4/1.8 x 30 mm, 96 teeth
3 601 M43 000: Saw blades for fibre-cement plates
Expert for Fibre Cement
305 x 2.2/1.6 x 30 mm, 8 teeth
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
English | 47
Article number
1 600 A01 ZE5
0 601 B12 100
0 601 B12 400
0 601 B12 300
0 601 B24 000
2 608 837 741
2 608 837 742
2 608 837 744
2 608 644 527
2 608 644 528
2 608 644 529
2 608 837 782
2 608 644 547
2 608 644 559
1 609 92A 5HG | (08.04.2020)