Additional Safety Instructions - YATO YT-82553 Bedienungsanleitung

GB
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are
tired or under eff ects of medicines or alcohol. Even a moment's inattention during work may lead to serious injuries.
Always use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks,
protective shoes, helmets and hearing protections permits to reduce the risk of serious injuries.
Avoid accidental activation of the tool. Make sure the switch is in the OFF position, before you connect the tool to the
mains. Holding the tool with a fi nger on the switch or connecting an electric tool when the switch is in the ON position may lead
to serious injuries.
Before you turn an electric tool on remove all the spanners and other tools, which have been used for adjustments. A
spanner left on rotating elements of the tool may lead to serious injuries.
Keep your balance. Maintain an appropriate position. It will permit to control the electric tool in case of unpredicted situations
during its operation.
Use protective clothes. Do not wear loose clothes or jewellery. Keep your hair, clothes and gloves away from moving
elements of the electric tool. Loose clothes, jewellery or long hair may get caught on moving elements of the tool.
Use dust extractors or dust containers, if the tool is equipped with any. Make sure they are properly connected. Using of
dust extractors permits to reduce the risk of serious injuries.
Operation of the electric tool
Do not overload the electric tool. Use a proper tool for the given purpose. A correct selection of the tool for the given work
will result in a more effi cient and safer work.
Do not use the electric tool if the switch is not functioning properly. A tool which may not be controlled by means of a switch
is dangerous and must be repaired.
Disconnect the plug from the mains socket before any adjustment, replacement of accessories or storage of the tool. It
will permit to avoid accidental activation of the electric tool.
Store the tool away from children. Do not allow untrained persons to operate the tool. An electric tool may be dangerous
in hands of an untrained person.
Make sure the tool is properly maintained. Check the tool in order to detects any unfi tting or loose moving elements.
Check whether the elements of the tool are not damaged. In case any damaged elements of the tool are detected, they
must be repaired before the electric tool is operated. Many accidents are caused by improper maintenance of tools.
Cutting tools must be sharp and clean. Properly maintained cutting tools are easier to control during work.
Use electric tools and accessories in accordance with the aforementioned instructions. Use the tool in accordance with
its purpose, taking into account the kind and conditions of work. Should the tool be used for other applications than the ones
it has been designed for, the risk of a dangerous situation increases.
Repairs
The tool may be repaired only by authorised service centres, which must use solely original spare parts. It will guarantee
a proper level of safety of operation of the electric tool.

ADDITIONAL SAFETY INSTRUCTIONS

Always observe the safety instructions in the operating manual as well as the other OHS instructions when using the machine.
Children or persons not trained for the use of sprayer guns are not allowed to use them.
Never point the device at people or animals.
Do not use sprayer guns for fl ammable materials.
Do not clean sprayer guns with fl ammable solvents.
Avoid hazards caused by spraying material and check the marking on the container or the information supplied by the manufac-
turer on spraying material, including the requirements for the use of personal protective equipment.
Do not spray any materials that may cause an unknown hazard.
Caution! A high-pressure jet can cause severe skin damage. Never allow any part of the body to come into contact with the jet.
Protective clothing does not provide suffi cient protection against injuries in the form of injections.
In case of injection of high-pressure jet under the skin, immediately consult a physician. Inform the physician about the substance
injected.
Do not eat, drink or smoke in the working area.
Always wear a respiratory protective mask to protect against harmful vapours.
Ensure adequate ventilation so that there is no accumulation of fl ammable vapours in the air of the working space.
Appropriate measures should be taken to prevent hazards caused by the substance being sprayed. Follow the instructions given
on the packaging or by the manufacturer of the substance to be sprayed.
Do not spray the substances listed as prohibited in this manual.
Do not spray materials of unknown composition.
Do not use the device without the nozzle cover installed.
Never use the device if any protecting elements or covers have been damaged.
O R I G I N A L I N S T R U C T I O N S
12