Test Run Method; Troubleshooting; How To Handle Problems With The Test Run - Mitsubishi Electric PEH-RP200MYA Installationshandbuch

12.3. Test run method

1 Turn on the power to the unit at least 12
hours before the test run.
TEST RUN
2 Press the
(Start this operation from the status of re-
mote controller display turned off.)
A
TEST RUN and current operation mode are dis-
played.
MODE
3 Press the
tivate mode, then check whether cool
COOL
air is blown out from the unit.
MODE
4 Press the
tivate mode, then check whether warm
HEAT
air is blown out from the unit.
FAN
5 Press the
fan speed changes.
6 Press the ON/OFF button to stop the test
run.

13. Troubleshooting

13.1. How to handle problems with the test run

Error code list: details
Remote controller
display
E0
E1, E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
F1
F8
A0
A2
A3
A6
A7
A8
EF
U2
U2
U3
U4
U6
UE
UL
F8
P1
P2
P4
P5
P5
P6
P6
P8
20
Downloaded from www.Manualslib.com
button twice continuously.
7
button to ac-
3,4
2
button to ac-
button and check whether
MELANS display
6831, 6834 Remote controller communication – reception error
6201, 6202 Remote controller board error
6832, 6833 Remote controller communication – transmission error
6831, 6834 Remote controller communication – reception error
6832, 6833 Remote controller communication – transmission error
6740, 6843 Communication between indoor and outdoor units – reception error
6841, 6842 Communication between indoor and outdoor units – transmission error
6840, 6843 Communication between indoor and outdoor units – reception error
6841, 6842 Communication between indoor and outdoor units – transmission error
6844 Indoor/outdoor connection wiring error, indoor unit overload (5 units or more)
6845 Indoor/outdoor connection wiring error (interference, loose)
6846 Excessive time in use
0403 Serial communication error
0403 Serial communication error
4103 Reverse phase, out of phase verification
4115 Faulty input circuit
6600 Duplicated M-NET address setting
6602 M-NET error in PH/W transmission
6603 M-NET bus busy
6606 M-NET communication error with P transmission
6607 M-NET error – no ACK
6608 M-NET error- no response
undefined Undefined error code
1102 Outlet temperature error
1108 CN23 Short-circuit Connector Unplugged
5104 Open/short in discharge temp thermistor
5105 Open/short in liquid temp or condenser/evaporator temp thermistor
4101 Compressor overcurrent interruption (51C operation)
1302 High pressure error (63H1 operation)
1300 Low pressure error (63L operation)
4115 Power synchronous idle circuit error
5101 Inlet sensor error
5102 Piping sensor error
2503 Drain sensor error
2502 Drain overflow protector operation
2500 Water leak error (PDH only)
1503 Freeze prevention operation
1504 Surge prevention operation
1110 Piping temperature error
manuals search engine
A
Note:
• Point the remote controller towards the indoor unit receiver while follow-
ing steps 2 2 2 2 2 to 6 6 6 6 6 .
TEST RUN
• It is not possible to run in FAN, DRY or AUTO mode.
ON/OFF TEMP
FAN AUTO STOP
5
MODE VANE AUTO START
6
CHECK LOUVER h
TEST RUN min
SET RESET CLOCK
Error details Problem location
Remote Controller
Remote Controller
Remote Controller
Indoor unit
Indoor unit
Indoor unit
Indoor unit
Outdoor unit
Outdoor unit
Outdoor unit
Outdoor unit
Outdoor unit
Outdoor unit
M-NET board
Outdoor unit
Outdoor unit
M-NET board
M-NET board
M-NET board
M-NET board
M-NET board
M-NET board
–
Outdoor unit
Outdoor unit
Outdoor unit
Outdoor unit
Outdoor unit
Outdoor unit
Outdoor unit
Outdoor unit
Indoor unit
Indoor unit
Indoor unit
Indoor unit
Indoor unit
Indoor unit
Indoor unit
Indoor unit