Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
General Safety Instructions
Read the operating instructions carefully before putting the
appliance into operation and keep the instructions including the
warranty, the receipt and, if possible, the box with the internal
packing.
•
The appliance is designed exclusively for private use
and for the envisaged purpose. This appliance is not fi t
for commercial use. Do not use it outdoors (except if it is
designed to be used outdoors). Keep it away from sources
of heat, direct sunlight, humidity (never dip it into any liquid)
and sharp edges. Do not use the appliance with wet hands.
If the appliance is humid or wet, unplug it immediately. Do
not put it in water.
•
When cleaning or putting it away, switch off the appliance
and always pull out the plug from the socket (pull on the
plug, not the cable) if the appliance is not being used and
remove the attached accessories.
•
Do not operate the machine without supervision. If you
should leave the workplace, always switch the machine off
or remove the plug from the socket (pull the plug itself, not
the lead).
•
Check the appliance and the cable for damage on a regular
basis. Do not use the appliance if it is damaged.
•
Do not try to repair the appliance on your own. Always
contact an authorized technician. To avoid the exposure
to danger, always have a faulty cable be replaced only by
the manufacturer, by our customer service or by a qualifi ed
person and with a cable of the same type.
•
Use only original spare parts.
•
Pay careful attention to the following "Special Safety Instruc-
tions".
Children
•
In order to ensure your children's safety, please keep all
packaging (plastic bags, boxes, polystyrene etc.) out of their
reach.
Caution! Do not allow small children to play with the foil as
there is a danger of suffocation!
•
To protect children from the dangers posed by electrical
appliances, make sure that the cable is hanging low and that
children do not have access to the appliance.
Special Safety Instructions
•
The machine should only be used under supervision!
•
Do not manipulate any of the safety switches!
•
Do not remove the lid during operation.
•
When mixing, keep your hands and other objects out of the
jug!
•
Warning: Please handle the blade with extreme care! There
is a danger of injury particularly when removing the blade
from the mixing vessel, when emptying the mixing vessel
and during cleaning!
•
Never pour liquids hotter than 60°C into the jug! Danger of
scalding!
•
Never use the mixer when it is empty!
05-UM 3047 25
•
The device must only be switched on after you have inser-
ted the seal in the hole in the lid.
•
Do not carry or lift the appliance during use. Always switch
it off fi rst and pull out the plug. Carry the appliance always
with both hands!
•
Clean the appliance only as described in „Cleaning".
Overview of the Components
1 Filling slot seal / Measuring jug
2 Lid
3 Mixer vessel
4 Round scale
5 Sealing ring
6 Knife block
7 PULSE switch - pulse operation
8 Safety switch
9 Motor housing
10 Rotary switch
11 Cable take-up
12 Rubber feet
Installation
Mains Lead
Unwind the required mains lead from the base.
Mixing Vessel
•
Place the mixing vessel in position in such a way that the
arrow is pointing to the symbol
•
Turn the mixing vessel in an anticlockwise direction until the
arrow is pointing to the symbol
Lid (see illustration C)
•
Place the lid in position so that the symbol
the arrow on the handle.
•
Turn the lid in a clockwise direction until the lever is pointing
to the arrow on the handle. This is the operating position, as
shown in illustration C. Please also read the section on the
„Safety Switch".
Important notice on the safety switch
The universal mixer is fi tted with a safety switch which prevents
the motor from starting up if the container and lid are not in place
(danger of injury).
When the vessel is put in place the safety pin presses on to the
safety switch of the motor housing. The universal mixer can now
be switched on. If the motor does not start, check that the mixing
vessel and lid are correctly fi tted in place.
Seal and Knife Block (see illustration B)
The knife block can be removed if necessary, e.g. for cleaning.
•
You can release or tighten the knife block by turning it in an
anticlockwise or clockwise direction.
•
When you reinsert the knife block, please ensure that the
seal forms a tight closure and that the container is tight.
on the motor housing.
on the motor housing.
is pointing to
25
31.07.2006, 12:24:54 Uhr
Werbung
Inhaltsverzeichnis
