Panasonic Toughbook CF-20 Serie Bedienungsanleitung Seite 12

First-time Operation
NOTE
l To set the password, proceed as follows.
A Click (Start) - (Settings) - [Accounts] - [Sign-in options].
B Click [Add] under "Password".
l Set the key entry mode to English ("ENG") and enter characters.
The keyboard layout can be added or changed in the following steps.
A Click (Start) - (Settings) - [Time & language] - [Region & language].
B Click a language and click [Options].
C Click [Add a keyboard] and choose a keyboard from the list.
l Remember your password. If you forget the password, you cannot use Windows. Creating a password reset disk beforehand is recommended.
l Depending on the version of Windows 10,
puter can be used in this state.
Refer to è Operating Instructions - Reference Manual "Advanced Operation" "Security Measures" "Device encryption" about settings.
l PC Information Viewer
This computer periodically records the management information of the flash memory, etc. The maximum data volume for each record is 1024 bytes.
This information is only used for estimating the cause in the case when the flash memory goes down by any possibility. They are never sent to outside via net-
work nor used for any other purpose except for the purpose described the above.
To disable the function, add the check mark for [Disable the automatic save function for management information history] in [Hard Disk Status] of PC Information
Viewer, and click [OK].
Then follow the on-screen instructions.
(è Operating Instructions - Reference Manual "Troubleshooting" "Checking the Computer's Usage Status")
12
5 Setup Windows
Select language and click [Next].
Follow the on-screen instructions.
l The computer restarts several times.
l After the computer is turned on, the screen remains black or unchanged for a while, but this is not a
malfunction. Wait for a moment until the Windows setup screen appears.
l During setup of Windows, use the touchpad and clicking to move the pointer and to click an item.
l Setup of Windows will take approximately 5 minutes.
Go to the next step, confirming each message on the display.
l You can set the Wireless Network after the setup of Windows is complete.
If "Let's connect you to a network" is displayed, you can select [Skip for now].
l We recommend that you set the password after the setup of Windows in complete.
CAUTION
l You can change the user name, image and security setting after setup of Windows.
l Use standard characters as a computer name: numbers 0 through 9, uppercase and lowercase letters from
A to Z, and the hyphen (-) character. Do not use the following words and characters for user name: CON,
PRN, AUX, CLOCK$, NUL, COM1 to COM9, LPT1 to LPT9, LPT, &, space.
If the error message "The computer name is not valid" appears, check if characters other than the above
are not entered. If the error message still remains on the display, set the key entry mode to English ("ENG")
and enter characters.
6 Restart the computer
A Click (Start).
B Click (Power) - [Restart].
l A portion of the Panasonic PC Settings Utility functions will be enabled after the computer restarts.
NOTE
l When the "Emergency notification setting" screen appears, read the on-screen messages carefully. Follow
the on-screen instructions. You can set the "Emergency notification setting" after the setup of Windows is
complete.
7 Update the on-screen manual
A Connect to the internet. Sign in to Windows as an administrator.
For further information, refer to
B Update the on-screen manual.
Click (Start) - [Panasonic PC Manual Selector].
Follow the on-screen instructions.
8 Create a recovery disc
A recovery disc allows you to install OS and restore its factory default condition, in case, the recovery partition
of the flash memory is damaged.
We recommend creating a recovery disc before you begin using the computer.
Refer to è Operating Instructions - Reference Manual "Important Operation/Settings" "Create a Recovery
Disc" about creating the disc.
may be added on the icons such as the C drive on Windows Explorer if the encryption is not completed. The com-
will disappear when the encryption is completed, or the "Device encryption" function is set to off.
Connect to a network.