Pa-4300Ptt; 12 Desk Microphone Pa-4300Ptt; 13 Zone Paging Microphone Pa-2400Rc - Monacor PA-6010Z Bedienungsanleitung

32 Cover plate; will be replaced by a connec-
tion plate when specific insertion modules
are installed
33 PA-6010Z only: Volume control for addi-
tional 60 W amplifier; this amplifier will
only operate for announcements that
are made via a zone paging microphone
PA-2400RC for which less than three zones
have been selected .
34 Jack for connection of the zone paging
microphone PA-2400RC
35 Jack for connection of the desk micro-
phone PA-4300PTT
Note: The desk microphone uses the input chan-
nel CH 1 . Make sure that the phantom power
supply for the input CH 1 is activated and that
the input jack CH 1 is not used .
36 DIP switches MIC PRIORITY to set the prior-
ity for the input channels CH 1– CH 3
1.2 Desk microphone PA-4300PTT
(separately available accessory)
37 DIP switch CHIME;
in the position ON, the chime will sound
first when the button TALK (43) is pressed
38 DIP switch PRIORITY;
OFF: An announcement will be made in
the PA zones selected at the ampli-
fier .
ON: All zone outputs will be switched
on as long as the button TALK (43)
is pressed .
39 Switch MASTER/SLAVE to define the
priority when multiple microphones
PA-4300PTT are used
SLAVE: Other microphones switched to
MASTER will take priority .
MASTER: The microphone will take priority
over the microphones that are
switched to SLAVE .
40 RJ-45 jack OUTPUT for connection to
the jack PA-4300PTT (35) of the amplifi-
er or to the jack LINK (41) of a different

PA-4300PTT

41 RJ-45 jack LINK to connect another micro-
phone PA-4300PTT
A maximum of 3 interconnected micro-
phones can be connected to the amplifier .
42 Microphone cartridge with windshield
43 Button TALK; to make an announcement,
keep the button pressed and, if applicable,
wait for the chime to sound; when the
button is pressed, the green LED TALK
above the button will light up
The red LED BUSY will indicate any
announcements that are being made via
a different PA-4300PTT .
1.3 Zone paging
microphone PA-2400RC
(separately available accessory)
44 Jack 24 V ⎓ for additional power sup-
ply via a power supply unit with a low
voltage plug 5 .5 / 2 .1 mm (outer/ inner
diameter); observe the polarity: centre
contact = ⊕
The additional power supply unit will be
required when the amplifier does not pro-
vide sufficient power [when the LED AMP
POWER (55) starts flickering, e . g . because
more than 3 PA-2400RC are connected or
the cable is very long] .
45 RJ-45 jack LINK to connect another
PA-2400RC
46 RJ-45 jack OUTPUT for connection to the
jack PA-2400RC (34) of the amplifier or to
the jack LINK (45) of a different PA-2400RC
47 DIP switches for the bus address and for
line termination
Prior to connecting the PA-2400RC to
the amplifier, use the switches 1– 5 to
set different address numbers at all the
PA-2400RC to be connected (
7 .5 .1) .
At the final PA-2400RC of the microphones
connected in a chain, set the switch 6 (TER-
MINATION) to the position ON to activate
the terminating resistor .
48 DIP switches
Switch 1 (PRIORITY) – When the switch
is in the position ON, the PA-2400RC will
take priority over the other PA-2400RC
for which this function has not been ac-
tivated and will be able to interrupt their
announcements .
Switch 2 (COMPRESSION) – When the
switch is in the position ON, the dynamics
of the microphone signal will be attenuat-
ed to reduce distortions when announce-
ments at a high volume are being made .
Switch 3 (CHIME ON/OFF) – When the
switch is in the position ON, a chime will
sound first when the button TALK (52) is
pressed:
4-tone chime
when switch 4 is in the position ON;
2-tone chime
when switch 5 is in the position ON and
switch 4 is in the upper position
Switch 6 – Definition of the amplifier to be
used with the zone paging microphone:
Position ON: PA-6010Z (10 zones)
Upper position: PA-6020Z (20 zones)
49 Control CHIME to adjust the volume of
the chime
50 Control MIC to adjust the volume of the
announcements
51 Microphone cartridge with windshield
52 Button TALK; to make an announcement,
keep the button pressed and, if applica-
ble, wait for the chime to sound; when
the button is pressed, the LED above the
button will light up
53 Button RECALL to save or call up a group
of zones
To save the selected zones, keep the but-
ton pressed until the LED ON (55) stops
flashing .
To call up the saved group, briefly press the
button . When the button is pressed again,
the previous selection will apply .
54 Zone selection buttons
Z1– Z10:
Z1– Z 20:
ALL CALL: all zones of the corresponding
☞ chapter
55 Status indicator LEDs
ON – power indicator;
will flash when zones are being saved with
the button RECALL (53)
BUSY – will light up during an announce-
ment; will flash when announcements of
a higher priority are being made
MIC FAULT – will indicate microphone
failures
AMP POWER – will indicate power supply
via the amplifier; will flicker when the sup-
ply voltage is insufficient
SIGNAL – will light up when a microphone
signal or chime signal is available
56 Operating buttons to call up saved messag-
es for the insertion module PA-1120DMT
The buttons have the same functions as
the corresponding buttons at the module .
zones 1–10 (with PA-6010Z)
zones 1– 20 (with PA-6020Z)
row of buttons
When the button is pressed
again, the previous selection
will apply again .
13