Inhaltsverzeichnis
Werbung
Compliance Information
FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.
The remote controller is designed to meet the requirements for exposure
to radio waves established by the Federal Communications Commission
(USA). These requirements set a SAR limit of 1.6 W/kg averaged over one
部件名称
铅 (Pb)
线路板
外壳
金属部件（铜合金）
内部线材
其他配件
本表格依据 SJ/T 11364 的规定编制。
○：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
×：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。（产品符合欧盟 ROHS 指令环保要求）
KCC Compliance Notice
"해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니
다 ."
"해당 무선설비는 운용 중 전파혼신 가능성이 있음"
NCC Compliance Notice
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不
單元Ｕ nit
鉛 Lead
(Pb)
線路板
－
外殼
○
排針
○
其他
－
備考 1.〝超出 0.1 wt %〞及〝超出 0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準值。
備考 2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考 3.〝－〞係指該項限用物質為排除項目。
汞 (Hg)
×
○
×
○
×
○
×
○
×
○
設備名稱：DJI Smart Controller Enterprise，型號（型式）：RM500-ENT
汞 Mercury
鎘 Cadmium
(Hg)
(Cd)
○
○
○
○
○
○
○
○
gram of tissue. The highest SAR value reported under this standard during
product certification for use when properly worn on the body
ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada's licence-
exempt RSS(s). Operation is subject to the following two conditions: (1)
This device may not cause interference.(2)This device must accept any
interference, including interference that may cause undesired operation of
the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil
est conforme aux CNR d'Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :(1)L'appareil
ne doit pas produire de brouillage; (2)L'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
This equipment complies with ISED radiation exposure limits set forth for
an uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.The portable device is designed to meet the requirements for
exposure to radio waves established by the ISED.
These requirements set a SAR limit of 1.6 W/kg averaged over one gram
of tissue. The highest SAR value reported under this standard during
product certification for use when properly worn on the body.
Cet équipement est conforme aux limites d'exposition aux rayonnements
ISED établies pour un environnement non contrôlé. L'utilisateur final
doit suivre les instructions spécifiques pour satisfaire les normes. Cet
émetteur ne doit pas être co-implanté ou fonctionner en conjonction
avec toute autre antenne ou transmetteur. Le dispositif portatif est conçu
pour répondre aux exigences d'exposition aux ondes radio établie par le
développement énergétique DURABLE.
Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme
de tissu. La valeur SAR la plus élevée signalée en vertu de cette norme
lors de la certification de produit à utiliser lorsqu'il est correctement porté
sur le corps.
有害物质
镉 (Cd)
六价铬 (Cr
○
○
○
○
○
○
○
○
○
○
得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾
現象時，應改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之
無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電
機設備之干擾。
注意：
應避免影響附近雷達系統之操作。
高增益指向性天線只得應用於固定式點對點系統。
限用物質及其化學符號
多溴聯苯 Polybrominated
六價鉻 Hexavalent
+6
chromium(Cr
)
○
○
○
○
+6
)
多溴联苯 (PBB)
多溴二苯醚 (PBDE)
○
○
○
○
○
多溴二苯醚 Polybrominated
biphenyls
diphenyl ethers (PBDE)
(PBB)
○
○
○
○
○
○
○
○
○
○
○
○
○
93
Werbung
Inhaltsverzeichnis
