Installation Instructions - Steinbach 060935 Bedienungsanleitung

Preface
Many thanks for purchasing this Steinbach product. We continually de-
velop and enhance our items, however, should this product be faulty, we
apologise for any inconvenience and politely ask you to get in contact
with our service centre.
Read operating manual and store safely
Instruction manual for Wireless LED underwater spotlights
for liner pools
This instruction manual relates to the product stated above. It contains
important information on starting your product for the fi rst time and how
to operate it. Carefully read through the instruction manual - particularly
the safety instructions - before using this product. Non-compliance with
this instruction manual may lead to major injuries or damage to your
product. The instruction manual is based on standards and regulations
applicable within the European Union. If the product is being used ab-
road, please follow any country-specifi c guidelines and laws. Store the
instruction manual in a safe location for later consultation and submissi-
on to third parties, where applicable.
Intended use
This product is solely intended for private use and is not suitable for
commercial use.
A skimmer is a surface vacuum cleaner which adapts to the surface
level of the water. This guarantees that only the upper few centimetres
of the surface is vacuumed. The perfect water level for you skimmer
is between the middle of the skimmer and the upper third. This is the
only way to guarantee that the fi lter unit does not run dry. It is absolu-
tely necessary to use the skimmer basket. In addition, a fl oor vacuum
cleaner can be attached by the integrated suction plate. Only use
the product as described in this instruction manual. Any other use is
considered improper use and may lead to personal injury or damage to
property. This item is not a toy. The manufacturer or retailer assumes no
liability for damage resulting from improper or incorrect use.
Warnings and safety instructions
Read and observe all instructions. Non-compliance with these
warnings and instructions may result in damage to property,
severe personal injury or even death. These product warnings,
instructions and safety regulations are extensive but cannot cover
all potential risks and dangers and are thus not to be considered
exhaustive. Please be cautious and assess potential dangers
appropriately. Incorrect use/handling of the product can lead to
life-threatening situations.
Caution! Leave repairs to experts in order to prevent hazards.
Consult a specialist workshop. Liability is waived and warranty
claims expire if repairs are carried out independently of if the pro-
duct is improperly installed or used incorrectly. Only original parts
corresponding to the original product specifi cations may be used
during repairs.
WARNING! Hazardous for children and persons with reduced phy-
sical, sensory or mental abilities (such as the handicapped, elderly
individuals with impaired physical and mental abilities), or those
with a lack of experience and knowledge. Children must not be
allowed to play with this product. Cleaning may not be performed
by children and persons with reduced physical, sensory or mental
abilities.
NOTE! Risk of damage! This product may be damaged through
improper use.
Check scope of delivery
NOTE! Risk of damage! The product may be damaged if you open the
packaging with a sharp knife or other sharp objects without due care
and attention. Please open the packaging very carefully.
■ Remove the product from the packaging.
■ Check that all included items have been delivered in full. Sketch/photo
L1.
■ Check whether the item, or parts thereof, exhibit damage. If there is
damage, do not use the product. Get in contact with the service ad-
6
dress stated at the end of the manual.

Installation instructions

To avoid any blinding effects, the spotlights
away from the property and the usual line of sight to the swimming pool.
So you don't have to empty the pool when changing the
commend installing the lamps in areas which are
the upper edge of the pool.
Before installation, check that the sealing nut (No. 8 + 20) is fully tighte-
ned.
The spotlights should be placed on the wall of the pool about 400- 700
mm away from the surface of the water (Fig. 1)
The procedure for attaching the housing to the pool wall depends on
whether the lights are for a concrete pool or a ready-made pool.
Concrete pool
To install underwater lighting in a concrete swimming pool, the housing
(No. 12) should be fi xed into the wall of the swimming pool (Fig. 2).
Ensure that the cable outlet is on the upper side of the housing.
Ready-made pools
To install lighting in a ready-made pool, cut a circular hole with a diame-
ter of 270 mm (Fig. 2).
From the inside, insert the housing (No 12) with one of the sealing rings
(No 17.) attached on top. Fix the housing and the swimming pool panel
using S screws or bolts (not included). When the lining is in position,
fi x the clamp (No 18) with the other sealing rings (No 17) and with 16
screws included (No 19) (Fig, 3).
Ensure that the cable outlet stays on the upper side of the housing.
After installing the housing and the clamp, mount the under water
lighting in a ready made pool to connect the light to the mains, pass the
cable through the sealing nut (4). Tighten the sealing nut until you can
check that the cable gives when you pull on it by hand.
Take the necessary precautions to ensure you leave 1.5 m of coiled ca-
ble on the base of the underwater lighting (No.11) so you are able to put
the light on the edge of the pool, or you can remove it when changing
the bulb or during other necessary maintenance (Fig. 4).
Push the whole lighting components into the housing (Fig. 5).
Tighten the two M-6 x 70 screws (No 15) until the fi xing bracket fi ts
securely on the inner wall of the housing (Fig. 7).
Initial use
Ensure the electricity supply coming into the light is not greater than 12
V. The underwater lighting should only be used underwater, se-cured
to the vertical walls of the pool. Never turn on the light when it is not
underwater.
Remote control for LED PAR 56 (optional)
This remote control has the following colour programmes:
Button 1 RGB (all LED's light up)
Button 2 B LEDs' light up blue
Button 3 R LED's light up red
Button 4 G LED's light up green
Buttons 5 - 11 Various changing colour programmes
Button 12 Switch off.
Please note: Wait 2 seconds before pressing another colour pro-gram-
me.
Technical data
■ LED-light 13 W with RGB colour changer
■ Rated supply 12 V
■ Electricity supply Alternating current
■ Power PAR 56, 12 V, Alternating current
■ Protection IPX 8
■ Should only be used with a swimming pool safety transformer!
■ Only turn the lighting on underwater!
060935_v1911 EN
should be installed facing
lamps, we re-
easily accessible from