Redmond SkyKettle RK-M216S-E Gebrauchsanleitung Seite 8

Remote control of the RK-M216S-E kettle is only possible if the Bluetooth function is
enabled.
2. Download the Ready for Sky application from the App Store or Google Play (de-
pending on the operating system of your device) to your smartphone or tablet.
Check the minimum supported version of the operating system on the official website
of www.redmond.company or in the description of the application in the App Store and
Google Play.
3. Start the Ready for Sky application, create an account, and follow the on-screen
prompts.
4. In the standby mode, press and hold down the button
appliance will produce three short beeps. During the connection, the temperature
indicators will come on alternately. Once the connection is established, the ap-
pliance will produce three short beeps.
If the Bluetooth function is disabled or the connection is not established within
30 seconds, the appliance will produce two short beeps and enter the standby mode.
5. To disable remote control, press and hold down the button
is produced. When the connection fails, the temperature indicators will blink.
To ensure stable communication, the mobile device should be no more than 15 meters
away from the appliance.
Appliance control via the wireless network. Instruction on the R4S Gateway applica-
tion installation is available through the link: www.readyforsky.com/r4sgateway
Bluetooth function
To enable Bluetooth:
1. Remove the kettle from the base.
2. Press and hold down the buttons
3. The heating temperature indicators will come on for a few seconds and go off.
To disable Bluetooth:
1. Remove the kettle from the base.
2. Press and hold down the buttons
3. The heating temperature indicators will blink three times and go off.
Water Boiling
1. Remove the kettle from the base. Press the lid release button.
8
for a few seconds, the
until a long beep
and to place the kettle back on the base.
and to place the kettle back on the base.
2. Pour water into the kettle, water level should be between the MIN and MAX points
on the scale. If water level is higher than MAX point, the boiling water may be
splashed. In case of water undersupply the appliance may be switched off in
advance.
ATTENTION! The unit is intended only for water heating and boiling.
3. Close the kettle lid and set the kettle to the base. The appliance will be oper-
ated only if it is properly fixed.
4. Plug in the appliance. The heating temperature indicators will flash, the appliance
will switch to the standby mode.
5. Press the button . The appliance will produce a beep, the operation status
indicator will come on, the boiling process will start.
During the heating process, the operation status indicator will change its color.
6. At the end of the water heating, the appliance will produce three short beeps, the
heating indicator will turn off and the appliance will enter the standby mode (no in-
dication).
7. To interrupt the water heating process, press
base.
Press the buttons on the control panel only with your fingertips, as shown in figure
(page 4). Pressing with your nails can damage the buttons!
A2
Water Heating Without Boiling
1. To heat water without boiling to 40, 55, 70, 85°C in the standby mode, select the
necessary temperature using (the indicator will come on next to the selected
value), press .
If the temperature in the kettle is higher than the adjusted heating temperature, three
audible signals will be heard after pressing
Warm mode.
2. At the end of the water heating, the appliance will produce three short beeps
and switch to the Keep Warm mode (Keep Warm value indicator and operation
status indicator are on).
3. To interrupt the Keep Warm mode, press
Temperature maintenance mode
This mode provides maintenance of the selected temperature 40, 55, 70, 85°С for 12
hours. If the temperature drops lower than the selected value, the heating element will
again or remove the kettle from the
, the appliance will switch to the Keep
or remove the kettle from the base.