Salewa TOXO Bedienungsanleitung Seite 6

[EN]
A GENERAL
Please read this information carefully before using the product and observe the instructions contained
herein. Failure to adhere to the following instructions can adversely affect the level of protection pro-
vided by this helmet.
The product is a mountaineering helmet, primarily designed for impact protection against rock
fall and offering protection to climbers during a fall. It is essential that you familiarise yourself
with this product before using it for the first time.
Please note the following information:
Mountaineering and climbing are dangerous sports that can involve unforeseeable risks. You
are responsible for any activities that you undertake and any decisions that you make. Please
find out about the risks involved in these type of sports prior to practising them. SALEWA recom-
mends full training by appropriate personnel (e.g. mountain guides, climbing trainers) before un-
dertaking any mountaineering or climbing activities. In addition, anyone practising these sports
is fully responsible for finding out about the proper course of action and techniques required
for the safe performance of any rescue operations. The manufacturer is not held liable in any
form for the consequences of abuse or incorrect use of equipment. Please also take note of the
certification details relevant to any other protective equipment components used.
This product is made in conformity with PPE regulation (EU) 2016/425.
You can view the EU Declaration of Conformity under www.salewa.com.
The product meets the third category for personal protective equipment (PSA)
B INSTRUCTIONS FOR USE
Only use the product for the purpose for which it was constructed and never burden it beyond
its limits.
: Danger to life
: Risk of injury
: Correct use
This product protects from rock fall and impacts and corresponds to the standard EN
12492:2012 .
Mountaineering helmets are headwear primarily intended to protect the upper part of the wear-
er's head against hazards which might occur during activities carried out by mountaineers. In
particular, these helmets are designed to absorb the energy produced during the collision by
reducing the intensity of the trauma suffered by the head. However, wearing a helmet cannot
prevent death or permanent disability.
ADJUSTING THE HELMET
Warning: A helmet can only provide optimum protection if it is properly and correctly fitted to
match your individual head size and shape. If this is not the case, DO NOT USE THE HELMET.
Swap it for another size or another model. A helmet that does not properly fit your head, or which
is too loose, will significantly impair the helmet's protective capability.
Illustration 1 - Adjusting helmet fit to your head size: First, expand the headband to its max-
imum dimensions via the adjustment wheel (turn anti-clockwise) and put the helmet on. Then
turn the wheel clockwise until the headband sits snug to your head. To get the perfect fit, you
can slide the headband vertically up or down at the back.
Illustration 5 - Magnetic buckle: To close: Bring both buckle ends together so that they slot into
one another. The magnetic buckle closes with a loud click. The Salewa logo should be on the
outside. To open: Slide both buckle ends away from one another sideways.
Plug buckle: To close: Push both buckle ends one into another so that they slot together. The
plug buckle closes with a loud click. To open: Press the buckle laterally.
Plug buckle: To close: Push both buckle ends one into another so that they slot together. The
plug buckle closes with a loud click. To open: Press the buckle laterally.
Illustration 2 – Adjusting the chin strap: The chin strap should sit at the sides of your head and
is fastened with the buckle under your chin. For a snug and comfortable fit, the strap length can
be adjusted under your chin. To position the strap properly at the sides of your head, open the
clips and adjust the strap length to fit your head shape so that the strap sits below your ears on
both sides. The straps must not cover your ears. When the buckle is closed, the chin strap should
not apply any pressure on your Adam's apple.
Illustration 4 – Check:
When the chin strap is fastened and the headband is flat to your head, ensure that the helmet is
sitting level horizontally and that it cannot slip forwards or backwards.
Illustration 3 - Attaching a headlamp: To attach a headlamp to your helmet, slide the headlamp
strap under the flexible clips on the outer shell and position the lamp at the front of the helmet.
C SAFETY INSTRUCTIONS
Always check the condition of your helmet first before using it. Check all straps, attachment
parts and make sure that the adjustment elements on the headband function properly.
Make sure that the helmet shape is not deformed and that it does not have any other visible
damage.
WARNING: Please note that your helmet has been designed to absorb the maximum amount of
force during impact. This is affected by the helmet deforming, which can cause it to incur dam-
age or be rendered unfit for use. However, this is not always visible to the naked eye.
For this reason, the helmet must be replaced immediately following any significant impact in
cases such as a climber fall or as a result of rock or ice fall, even if the damage is not visible.
Extreme temperatures (below -20°C/-4°F and above +35°C/95°F), paint, solvents, adhesives/
glues or stickers can all alter the physical characteristics of the helmet, and therefore may only
be used with instructions or permission provided by the manufacturer.
·If there is the least doubt about the safety of the product, it is to be replaced immediately.
D LIFESPAN
The helmet's lifespan is very dependent on the following factors: regularity of use, type of use,
external influences, correct maintenance and cleaning method.
SALEWA explicitly recommends replacing any safety equipment (PSA/PPE equipment) after a
maximum of 10 years from the date of production, regardless of whether the product has been
used regularly or not. Extreme and very demanding usage can even lead to a lifespan of less
than one year.
If the helmet suffers any extreme shock loads such as those that occur following a climber
falling, or in cases of rock and ice fall, it must be replaced immediately even if there are no
visible signs of damage.
E CLEANING, STORAGE, TRANSPORT AND SERVICING
Storage
You should store your helmet somewhere dry, cool and well ventilated, away from direct sunlight.
Avoid storing the helmet near any heat sources, or anywhere where it is exposed to direct or
persistent UV rays or extreme temperatures. Do not store your helmet in your backpack. Ensure
that your helmet never comes into contact with aggressive chemicals such as battery acid,
solvents or salt.
Cleaning and maintenance
Heavy soiling on your helmet can be washed off with mild soap but do not use any chemical
cleaning products or solvents. Rinse your helmet thoroughly after cleaning and dry it all over
with a towel. Do not carry out any repairs or modify your helmet yourself. If you notice that the
helmet is damaged, you should replace it. Any incorrect action performed on your helmet or
any changes made to it can adversely affect the helmet's protective capability. If you have any
questions regarding replacement parts for your helmet, please contact your SALEWA specialist
dealer. The product may neither be modified nor be repaired.
Transport
Protect your helmet from any mechanical wear or damage, solar radiation, chemicals or dirt. The
best approach is to get a protective bag for your helmet and/or a special storage and transport
container. Your helmet is delivered in a heavy-duty box which can be used for this purpose.
F IDENTIFICATION LABELS
Illustration 6 Product markings
Dolomiticert S.c.a.r.l. Notified Body n 2008 Z.I. Villanova, 1 32013 Longarone Italy
: Manufacturer's brand
XXXX: Product name
"Helmet for mountaineering": Product designation: Climbing Helmet
Notified body xxxx CE Number of certifying body
CE Confirms adherence to the Ordinance (EU) 2016/425
Certified by: DOLOMITICERT S.C.A.R.L., Z.I. Villanova, 32013 Longarone (BL), Italy Number of in-
specting authority "2008"
Made in X: Country of origin
xxAmmyy:Index (Reference to current drawing)
A:Production batch (A = first batch of the production month)
mm: Month of manufacture (01 = January)
yy: Year of manufacture (13 = 2013)
EN 12492:2012, UIAA 106 The standard with which the product complies
SALEWA - Oberalp S.P.A., - Via Waltraud Gebert Deeg Strasse 4, I-39100 Bozen - Italy: Brand,
name and address of manufacturer