Troubleshooting - Steinbach APPcontrol Bedienungsanleitung

ommend keeping the cleaner between 10°C and 32°C in a shaded, well
ventilated place. Avoid direct sunlight at all times.We recommend attach-
ing the operating unit with a safety rope, to avoid any risk of the power
pack being pulled into the pool. Before use, please read the instructions
relating to trouble-shooting thoroughly.
Trouble shooting
Indicator Meaning
1H fl ash quickly Machine out of
with buzz water
All lights fl ash Power supply
quickly with buzz over load
1H+2H+3H fl ash Seal box leaking
quick with buzz
ALL+1H fl ash Pump over load
quick with buzz
WALL+2H quick Walking motor 1
with buzz over load
FLOOR+3H fl ash Walking moter 2
quick with buzz over load
ALL+WALL Cleaner present
+1H+2H fl ash abnormalvoltage
quick with buzz
ALL+WALL Abnormal com-
+FLOOR fl ash munication
quick with buzz
WALL+FLOOR Machine out of
+2H+3H fl ash water and could
quick with buzz not restart
WALL fl ash quick Machine turned
with buzz over
Pool cleaner does The pool cleaner
not drive up the has too little
wall completely. buoyancy.
Important Note
Figure 15 / Solution 1
Dismount the top and place two pieces of foam
diagonally from the center, on the inside of the lid
of your pool cleaner (Figure 15).
If your swimming pool cleaner still has too little
buoyancy after this step, then please also apply
solution 2.
Figure 16 / Solution 2
Place two more pieces of foam next to the pieces
already attached (Figure 16).
Instructions for sticking the foam pieces:
1. Remove the paper on the back of the foam.
2. Please note the different lengths of the foam pieces.
3. Press the foam piece from the inside (A) outwards (B) to fi nish the pro-
cess properly.
55 mm
55 mm
Suggestion
Put machine back into wa-
ter or wait until machine
restart automatically
Stop machine contact
after sale service person
Stop machine contact
after sale service person
Stop machine check the
impeller and pump
Stop machine check belt
and transmission system
Stop machine check belt
and transmission system
Stop machine contact
after sale service person
Check the cable between
cleaner and power supply
or contact the after sale
service person
Stop machine restart
machine manually after
cleaner sink
Turn over machine
manually
* Clean the fi lter container /
fi lter bag.
* Clean the pool walls of
slippery deposits such as
algae.
* Put the pool vacuum into
the pool at the optimum
water temperature. This is
between 10 ° C and 32 ° C.
* Check the drive belts and
brushes for wear and repla-
ce them if necessary.
* Make sure the pH is cor-
rect, between 7.0-7.4.
* Stick the included self-ad-
hesive polystyrene pieces
to the inside of your pool
cleaner (See Figure 15 -16)
A B
Technical data
■ Input voltage: 220(230) VAC
■ Frequency: 50 Hz
■ Output voltage: DC (direct current) 24 V
■ Rated power: 200 W
■ Cable length: 18 m
■ Width of cleaning drum: 465 mm
■ max. Cleaning area in swimming pool: 270 mÇ
■ Filter performance: 20mÑ/h
■ Filter grade 100 μm
■ Operating temperature (water): 10°C - 32°C
■ Crawl speed: 12m/min
■ Hydrolytic resistance class: Cleaner: IPX8; Power supply: IPX5
■ Surrounding temperature: 10°C - 32°C
■ Weight of the cleaner: 12.5 kg (without cable)
Service
Please do not send the equipment to us without authorisation, but
please contact our service centre initially! If the equipment has to be
collected, it must be packed securely and the invoice (copy) must the
enclosed. As soon as the unit reaches us, it will be checked for faults by
our claims department, and repaired. On conclusion of this work, your
equipment will be returned to you as quickly as possible. If this return
is not covered by the guarantee, the costs incurred will be calculat-
ed. Guarantee processing / guarantees are handled by the company
Steinbach VertriebsgmbH. The item will be repaired by the company
Steinbach VertriebsgmbH, however where no right of return exists it will
not be taken back.
Cleaning
Use conventional cleaning products. Do not use solvent-based or
abrasive cleaning agents/tools, i.e. no hard sponges, brushes etc.. The
cleaning robot is also suitable for basins with salt electrolysis if the salt
content does NOT exceed 0.5%! It is important to note that the robot is
rinsed with fresh water from the inside and outside after each cleaning
process in order to avoid damage to the unit!
Storage
The product must be thoroughly dried after cleaning. When the product is
not being used, store it in a well ventilated place out of direct sunlight. Avoid
direct sunlight. Make sure the room temperature is above 5°C in winter.
Disposal
Disposing of packaging: The packaging material has been selected
in view of environmental concerns and disposability and is therefore
recyclable. The paper and cardboard can be recycled, as can the plastic
coverings.
Disposing of the product: Applicable in the European Union and other
European states with systems in place for collecting and sorting recycla-
ble materials. Dispose of the product in accordance with any laws and
regulations applicable at your place of residence.
Old devices must not be placed in the household waste! Should the
robot become unusable, each customer is legally obligated to separa-
te old devices from the household waste, e.g. take the device to your
community/ area collection point. It is therefore ensured that old devices
are professionally recycled and negative effects on the environments
are mitigated. For this reason, electrical devices are marked with the
symbol depicted here.
Warranty conditions
The respective country's legal provisions for warranty conditions shall
apply accordingly.
Declaration of conformity (CE)
The EU declaration of conformity can be requested via the address
shown at the end of this manual.
061023_v2004 EN
11