Maintenance - Makita 6835D Betriebsanleitung

SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 1)
• Always switch off the tool before insertion or removal of
the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while pressing the push buttons on both sides of
the cartridge.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If not, it may accidentally fall out
of the tool, causing injury to you or someone around
you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Setting for desired screw length (Fig. 2)
There are 3 positive-lock screw length settings. To obtain
the desired setting, pull out the stopper base while
depressing the lever until you see the number of the
desired screw length (indicated on the plate) appear to
rest on the very top edge of the casing. See the table
below for the relation between the number indicated on
the plate and the respective screw length ranges.
Number indicated
on the plate
25/28
32
40
Adjusting the driving depth (Fig. 3)
Depress the stopper base as far as it will go. While keep-
ing it in this position, turn the adjusting knob until the bit
tip projects approx. 5 mm from the stopper base. Drive a
trial screw. If the screw head projects above the driving
surface, turn the adjusting knob in the A direction; if the
screw head is countersunk, turn the adjusting knob in the
B direction.
Installing screw strip (Fig. 4 & 5)
Insert the screw strip through the screw guide. Then
insert it through the feeder box until the first screw
reaches the position next to the driving position.
Removing screw strip (Fig. 6 & 7)
To remove the screw strip, just pull it out in the direction
of the arrow. If you depress the reverse button, you can
pull out the screw strip in the reverse direction of the
arrow.
Carry hook (Fig. 8)
The carry hook is convenient for temporarily hooking the
tool. It can be installed on either side of the tool. When
installing or removing the carry hook, widen it by pressing
its lower portion in the direction of the arrow.
Screw length range
(mm)
25 – 28
28 – 35
35 – 41
Switch action (Fig. 9)
CAUTION:
• Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
To start the tool, simply pull the trigger. Release the trig-
ger to stop.
Driving operation (Fig. 10)
Switch on the tool by pulling the switch trigger. Hold the
tool squarely and firmly up against the driving surface. A
screw will be automatically carried to the driving position
and fastened.
CAUTION:
• Always check the bit carefully for wear before driving
operations. Replace a worn bit or poor fastening may
result.
• Always hold the tool squarely against the driving sur-
face. Holding it at an angle may damage the screw
heads and cause wear on the bit. This may also lead to
poor fastening.
• Always keep the tool firmly against the driving surface
until the driving is over. Failure to do so may cause
insufficient fastening of screws.
• Be careful not to drive a screw onto another screw
already fastened.
• Do not operate the tool without screws. It will damage
the driving surface.
• If the feeder box does not work smoothly when driving
screws, spray car wax (spray type) on the sliding sur-
faces. Never lubricate it.
Driving in corner (Fig. 11)
This tool can be used to drive at a position 15 mm away
from the wall as shown in Fig. 11.
CAUTION:
• Driving at a position closer than 15 mm to the wall or
driving with the stopper base in contact with the wall
may damage the screw heads and cause wear on the
bit. This may also lead to poor fastening of screws and
malfunction of the tool.
Installing or removing bit (Fig. 12 & 13)
Important:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before installing or removing
the bit.
Loosen the thumb screws which secure the casing. Pull
out the casing in the direction of the arrow. Press the dust
cover toward the plain bearing and pull out the bit. If the
dust cover cannot be moved as far as the plain bearing,
try it again after turning the bit slightly. To install the bit,
insert it into the socket while turning it slightly. After
installing, always make sure that the bit is securely held
in place by trying to pull it out.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before carrying out any work
on the tool.
To maintain product safety and reliability, repairs, mainte-
nance or adjustment should be carried out by a Makita
Authorized Service Center.
7