Herunterladen Inhalt Inhalt Diese Seite drucken

Operation; Shutting Down - Campingaz 200 SGR Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für 200 SGR:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
3. Close the valve on the regulator or gas cylinder.
(Fig. 14)
4. Screw or push the regulator onto the cylinder or onto
the valve on the gas cylinder.
5. Check that the air holes in the burner tube, close to the
injector, are not obstructed by dust or cobwebs.
D-1 CHECKING FOR GAS LEAKS
Do not check for leaks using a flame. Use a gas leak
detecting liquid.
1. Apply gas leak detecting liquid to the cylinder /
regulator / hose / appliance joints.
2. Open the gas supply (valve on the regulator or cylinder)
(Fig. 15-A).
3. Any gas leaks will be indicated by bubbles.
4. Shut off the gas supply (valve on the regulator or
cylinder) (Fig. 14).
5. The leak can be stopped by tightening any hose
connection or replacing any faulty component. The
appliance must not be used until the leak is stopped.
Important:
An overall inspection and leaks check must be carried
out at least annually and always after changing the gas
cylinder..
E - OPERATION
SAFETY PRECAUTIONS
Do not use your appliance at a distance closer than
20 cm to a wall or flammable object, nor closer than 1
metre to a ceiling.
WARNING: Accessible parts may be very hot. Keep young
children away.
Never touch the burner during or just after using the
equipment.
Position the equipment on a stable, horizontal surface
and do not move when in use.
Do not use a cooking vessel smaller than 12 cm or larger
than 20 cm in diameter.
In the event of a leak (smell of gas), close all valves.
Wait for the appliance to cool down completely before
handling it for storage.
After use, always close the valve on the regulator or gas
cylinder.
E-1 LIGHTING UP
Match Ignition (Fig. 15):
1. Open the gas supply (A) (valve on the regulator or
cylinder).
2. Put a lit match (B) near the burner from underside.
E-2 OPERATION
• It is recommended protective gloves to be worn to
handle components which may be very hot.
• Preheating: Before grilling, preheat the appliance for
about 10 minutes in full flame. When using the appliance
for the first time, preheat for about 20 minutes in full
flame in order to eliminate the smell of paint from new
components.
• A bluish discolouration of the hot plate is due to the
strong heat development. This is without any impact on
the quality of the used material.
• Note: In case the burner extinguishes whilst grilling,
close the gas valve immediately and wait 5 minutes to let
the gas be evaporated. Re-ignite the appliance after this
waiting time.
E-3 SHUTTING DOWN
Close the valve on the regulator or gas cylinder. (Fig. 14)
F - REMOVING OR CHANGING THE GAS
CYLINDER
Always work in a well-ventilated area, never in the presence
of a flame, spark of heat source.
1. Close the valve on the regulator or gas cylinder. (Fig. 14)
2. Disconnect the regulator from the gas cylinder.
3. Install the new gas cylinder.
4. Connect the regulator to the new gas cylinder (check
the condition of the regulator seal, before connecting
it to the gas cylinder).
G - STORAGE - SERVICING
If you take care of your appliance properly, you will be able
to enjoy using it for many years.
• Do not clean your appliance when it is being used. Wait
until it has cooled down to avoid burns caused by hot
parts (cooking grate, grease tray etc.).
• When cleaning, be careful to avoid clogging the burner
holes. If the holes are clogged, for example by food that
has spilled over, open them with a non-metal brush.
• Clean greasy parts with soap and water or a non-abrasive
detergent product.
• Store the device in a dry, ventilated place.
• If the device has not been used for 30 days, check to see
that cobwebs are not clogging the burner hose openings;
this could lead to decreased burner efficiency or to a
dangerous ignition of gas outside the burner.
• If the appliance will not be used for a long period of time,
disconnect the cylinder as indicated in section § F.
• Regularly check the condition of the hose and change it
if it shows signs of ageing or cracking (see section § C-2).
• In the case of the injector becoming clogged (the cylinder
still contains gas but the appliance will not light), do not
try to unclog it yourself. Return the appliance to your
retailer.
21
GB

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis