Battery Charge Indicator; Changing The Tool; Method Of Operation - Bosch GDR 18V-200 C Professional Originalbetriebsanleitung

16 | English
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Observe the notes for disposal.
Removing the Battery
The battery (6) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (7) unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery (6), press the release button (7) and
pull the battery out of the power tool. Do not use force to
do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Note: The state of charge of the battery is also displayed on
the user interface Status indications.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
1 609 92A 5D0 | (29.08.2019)
LEDs
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light

Changing the Tool

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Regularly clean the power tool's air vents. The motor's
u
fan can draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
Use application tool: GDR/GDX 18 V-200 C (see figure
A – B)
Pull the locking sleeve (2) forward, guide the application tool
(1) into the tool holder up to the stop and release the locking
sleeve (2) to lock the application tool.
Impact-proof screwdriver bits (17) can be inserted using a
universal bit holder with ball catch (16).
Impact-proof screwdriver bits (17) can be inserted using a
universal bit holder with ball catch (16).
Use application tool: GDX/GDS 18 V-200 C (see figure
to
B – C)
When working with an application tool, pay attention
u
that the application tool is connected securely to the
tool holder. When the application tool is not securely
connected with the tool holder, it can come off during ap-
plication.
Slide the application tool (18) onto the square drive of the
tool holder (1).
Due to the way the system operates, the application tool
(18) will move around slightly in the tool holder (1); this has
no influence on the function/safety.
Some application tools (e.g. double bits) cannot be safely
secured in the tool holder.
Capacity
Removing
60−100 %
Pull the locking sleeve (2) forward and remove the applica-
30−60 %
tion tool.
5−30 %
0−5 %
Operation

Method of Operation

The tool holder (1) (with the application tool) is driven by an
electric motor via a gear and impact mechanism.
The working procedure is divided into two phases:
Capacity Screwing in and tightening (impact mechanism in action).
80−100 %
Capacity
60−80 %
40−60 %
20−40 %
5−20 %
0−5 %
Bosch Power Tools