Technical Data; Noise/Vibration Information; Charging The Battery - Bosch UniversalImpact 18 Originalbetriebsanleitung

14 | English
(10) Handle (insulated gripping surface)
A)
(11) Universal bit holder
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Cordless drill/driver
Article number
Rated voltage
No-load speed
– 1st gear
– 2nd gear
Impact rate
Max. torque, hard/soft
screwdriving application ac-
cording to ISO 5393
Max. drilling diameter (1st/2nd gear)
– Steel
– Wood
Max. screw diameter
Tool holder
Max. impact drilling diameter
Weight according to
A)
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation and
during storage
Recommended batteries
C)
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 86 dB(A); sound power level
97 dB(A). Uncertainty K=5 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1:
2
Drilling into metal: a <2.5 m/s , K=1.5 m/s
h
Impact drilling into concrete: a =18 m/s
h
1 609 92A 5L3 | (15.01.2020)
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
UniversalImpact 18
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
3 603 JC8 1..
increase the vibration and noise emissions over the total
V= 18
working period.
To estimate vibration and noise emissions accurately, the
-1
min 0–400
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
-1
min 0–1350
This may significantly reduce vibration and noise emissions
-1
min 0–20205
over the total working period.
Nm 30/18
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
mm 10
Assembly
mm 30
mm 8
u
mm 10
u
mm 6
kg 1.3–1.6
°C 0 to +35
u
°C –15 to +50
PBA 18V...W-.
AL 18...

Charging the Battery

u
u
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
2
u
2 2
, K=3 m/s
Pull the plug out of the socket before carrying out any
work on the power tool.
Before any work on the power tool (e.g. maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the middle
position. There is risk of injury from unintentionally
pressing the on/off switch.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not use any other charger. The supplied charger is
matched to the lithium-ion battery that is fitted in your
power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Bosch Power Tools