Specifications - Makita GA4540R Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Slide switch
3-1. Indication lamp
5-1. Wheel guard
5-2. Bearing box
5-3. Screw
5-4. Lever
6-1. Screw
6-2. Lever
7-1. Wheel guard
7-2. Bearing box
7-3. Screw
8-1. Lock nut
8-2. Depressed center wheel
8-3. Inner flange

SPECIFICATIONS

Max. wheel thickness
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted
according to EN60745:
Model GA4540R, GA5040R
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Explanation of general view
9-1. Lock nut wrench
9-2. Shaft lock
10-1. Ezynut
10-2. Abrasive wheel
10-3. Inner flange
10-4. Spindle
11-1. Shaft lock
12-1. Arrow
12-2. Notch
14-1. Lock nut
14-2. Flex wheel
14-3. Plastic pad
14-4. Inner flange
15-1. Sanding lock nut
15-2. Abrasive disc
Model
Wheel diameter
Spindle thread
Rated speed
Overall length
Net weight
Safety class
noise level determined
) : 86 dB (A)
pA
) : 97 dB (A)
WA
GA4540R
115 mm (4-1/2")
303 mm
2.4 kg
ENE048-1
Model GA4541R, GA5041R
Sound pressure level (L
Sound power level (L
ENF002-2
Uncertainty (K) : 3 dB (A)
Model GA6040R
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
ENG905-1
Vibration
The vibration
determined according to EN60745:
Model GA4540R
Work mode : surface grinding with normal side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
4
15-3. Rubber pad
16-1. Marking A
16-2. Marking B
16-3. Marking C
16-4. Marking D
18-1. Lock nut
18-2. Abrasive cut-off wheel/
diamond wheel
18-3. Inner flange
18-4. Wheel guard for abrasive cut-off
wheel/diamond wheel
19-1. Wire cup brush
20-1. Wire wheel brush
21-1. Exhaust vent
21-2. Inhalation vent
GA4541R GA5040R
125 mm (5")
6.4 mm
M14 or 5/8" (country specific)
-1
11,000 min
325 mm 303 mm
2.6 kg 2.5 kg
/II
) : 84 dB (A)
pA
) : 95 dB (A)
WA
) : 87 dB (A)
pA
) : 98 dB (A)
WA
Wear ear protection
total value (tri-axial
) : 6.5 m/s
h,AG
2
GA5041R GA6040R
150 mm (6")
-1
9,000 min
325 mm 303 mm
2.7 kg 2.5 kg
ENG900-1
vector sum)
2