S Pecifications; O Perating Conditions; Achine - SUHNER ABRASIVE ROTOfera Originalbetriebsanleitung

2.2.4 s
Afety guArd
If a safety guard is supplied with the hand tool, it is
imperative that the safety guard be used.
2.3 s
pecificAtions
3-phase AC motor
Voltage 42/400/415V: 50Hz / 230/460V: 60Hz
Power Input
Power Output
Protection class
Type of protection
No-load speed 50Hz
No-load speed 60Hz
Sound pressure level 50Hz
Sound pressure level 60Hz
Sound power level 60Hz
Threaded connection for flexible shafts of type:
DIN 10
NA 4, NA 7, NA 10
G28
NA 4, NA 7, NA 10
2.3.2 V
iBrAtion mesurement VAlues of hAnd tools
BSG 10
Measurement value <2.5m/s
FSM 1:1
Measurement value 4.7m/s
WI 7, WI 10
Measurement value <2.5m/s
FH 12
Measurement value <2.5m/s
FH 10
Measurement value <2.5m/s
According to EN 60745.
The specified vibration value was measured with a
standardised test method and may differ from the
actual operating value. The specified value can be
used for product comparisons or for an introductory as-
sessment of work breaks.
2.4 o
perAting conditions
Temperature range during operation: 0 to +50°C
Relative air humidity: 90% at +30°C, 65% at +50°C
To avoid strong looping movements and beaming
of the flexible shafts, the working pressure must
be reduced.
1000W (1200W - 60Hz)
800W (906W - 60Hz)
IP44
850-12'000min
1'100-14'600min
79dB(A), K=3dB(A)
81dB(A), K=3dB(A)
92dB(A), K=3dB(A)
M10
see catalog
G28
see catalog
Test grinding wheel ø 100x25
2
/K=1.5m/s
Drive 7'000min
Test grinding wheel ø 180x6
2
/K=1.5m/s
Drive 8'000min
Test grinding wheel ø 50x6
2
/K=1.5m/s
Drive 15'000min
Test grinding wheel ø 80x10
2
/K=1.5m/s
Drive 12'000min
Test grinding wheel ø 80x10
2
/K=1.5m/s
Drive 15'000min
3.
handling
3.1 m

Achine

3.1.1 s
elect the speed
1
-1
-1
Pull the locking pin to disengage it (1). Set the speed you
want by pulling or twisting the eccentric (2).
You may set the speed only when the tool is
switched off.
3.1.2 s
tArting the mAchine
Before turning on the machine, make sure to re-
2
move wrenches and adjusting tools.
-1
When turning on, hold the flexible shaft extended.
During operation make sure that the flexible shafts have
2
large bend radius.
-1
Before starting the machine, hold the hand tool against
turning!
2
The machine has a high starting torque!
-1
Operate power switch of the machine.
2
3.1.3 m
Achine stop
-1
Power switch OFF.
Hold hand tool steady until the speed Zero is reached.
2
-1
3.1.4 s
hAft receptAcle
On production stop place shaft in the appropriate shaft
receptacle (type F + STM).
On prolonged interruption of work detach shafts
and hand tools and store shaft straight.
/ o
Peration
25