Maintenance; Faults / Solutions; Ec Declaration Of Conformity - Hozelock Pure Bedienungsanleitung

- If there is still some unused treatment product left, eliminate any residual
pressure remaining in the apparatus by operating the safety valve (Fig.
16). Recover any possible excess of product and rinse the sprayer again
as indicated above.
- Before using again, even if it is used again immediately, with a different
spraying solution, repeat the rinsing operation 3 consecutive times.
- Before using again, even if it is used again immediately, with the same
treatment product or a different one, check that the sprayer works properly
(especially the valve). treated in 1 min x nozzle output = 100 m²/20 m²/min
x 0.66L/min = 3.3 litres; i.e. 3.3-0.6 = 2.7 litres of water and 0.6 litres of
treatment product.
- This calculation is only given as an indication. During actual use, take into
account the information provided by the manufacturer of the treatment
product and the data on the nozzle output table.

MAINTENANCE

- Periodically, on re-use after overwintering and several times per season,
grease all the joints (with silicone grease for sprayers) and check that the
sprayer is working properly (especially the valve).
- Clean the nozzle and the nozzle holder (Fig. 20)
- Clean the lance filter (Fig. 21)
- Remove the pump (Fig.22)
- Grease or replace the valve and the seals (Fig.22)

FAULTS / SOLUTIONS

Problems
Make sure that all the connectors are fully tightened
Make sure that all the seals are lubricated and clean
Little or no
and are not damaged or worn. Replace them if
spraying
necessary (contact the customer service department).
Clean the nozzle and the filters
The spraying is
Clean the nozzle
not straight
Make sure that all the connectors are fully tightened
Make sure that all the seals are lubricated and clean
Leaks
and are not damaged or worn. Replace them if
necessary (contact the customer service department).
Safety valve DANGER: Do not pressurise the appliance Contact
defective the customer service department
WARRANTIES
EXTENDED COVER
Guarantee period and scope:
- We guarantee our products for a period specified in the specific manual
attached to the product or on the product from their date of purchase
(Compulsory Cover extended to 2 years + Extension of our Contractual
Warranty).
- On failure to present proof of the date of purchase of the products, the
Warranty is effective from the date of manufacture of the product (stated
underneath the product).
Warranty disclaimer:
This Warranty does not cover:
- Normal wear parts: seals, valves, handle, nozzle, piping, carrying straps,
rod and lever,
- Modified products,
- Products whose use contradicts the technical recommendations
stipulated in the User Manuals accompanying the product,
- Products used improperly,
- Products not undergoing regular maintenance,
- Product deteriorations (impacts, falls, crushing, etc.) originating from
negligence, improper maintenance, improper use or abnormal use of the
product,
- The replacement of a component after losing a component of the sprayer.
Warranty activation:
- We ask that you keep proof of purchase (invoice or legible till receipt), as
this will be requested on activation of the Contractual Warranty.
Solutions
- A product under warranty that has been repaired or replaced, remains
guaranteed for the remaining duration and under the original conditions of
the Contractual Warranty granted at the time of purchase. All returned
products become the property of HOZELOCK-EXEL when replaced by a
new product.
Legal Warranty
- The Mandatory Cover, the conditions of which are recalled hereinabove, does
not replace the Legal Warranty.
STATEMENT OF WARRANTY
General Terms and Conditions
Hozelock provides a manufacturer's warranty to the initial purchaser for each new
product produced by Hozelock that is sold by an authorised Hozelock supplier in
Australia or New Zealand. This warranty provides such initial purchaser with a
guarantee against faulty workmanship in manufacture and/or defective
components for the warranty period from the date of purchase.
The benefits given by this manufacturer's warranty are in addition to other rights
and remedies of the consumer under a law in relation to the goods to which this
warranty relates.
Making a Claim
If any product supplied by Hozelock is found to be defective due to faulty
manufacture and/or defective components within the warranty period, Hozelock
will repair or replace the product to the customer providing:
• proof of purchase is provided to Hozelock or its authorized supplier of the
relevant goods
• the fault is not caused by misuse, neglect, adjustments and or modification by the
consumer
• the consumer presents the defective product at the premises of the authorised
supplier of that relevant Hozelock product
• failure has not occurred through normal wear and tear.
The product will be repaired or replaced at Hozelock's cost however any costs
incurred to obtain warranty consideration or service is the consumer's
responsibility, including shipping and handling, travel expense, lost time, or pickup
and delivery.
Australia
Our goods come with guarantees that cannot be excluded under the Australia
Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
Hozelock Australia Pty Ltd (ABN 83 154 891 648).
Unit 22 / 456 St Kilda Road, Melbourne, Victoria 3004
Phone: 1300 275175
Email: australiamail@hozelock.com
New Zealand
The manufacturer's warranty is in addition to the rights and remedies provided by
the New Zealand Consumer Guarantees Act
Distributed in New Zealand by:
Horticom (Company No. 463657)
651 Rosebank Road, Avondale, Auckland 1026
Phone: 09 828 4408
EC

EC DECLARATION OF CONFORMITY

I the undersigned Jérôme BOULMIER – Quality Manager - certify with this
declaration that the product
Type: Pressure sprayer
Brand : HOZELOCK
Model: Hozelock PURE 7L Sprayer
Ref : 4550
Has been developed, designed and manufactured according to all the
relevant provisions in the "Machine Safety Directive" 2006/42/EC
Signed in Villefranche,
18/08/2016